MASSO G3 User Manual

MASSO
MASSO Documentation
8.21. G82 – Drilling Canned Cycle With Dwell
.................................................................... 219
8.22. G83 – Peck Drilling For Deeper Holes
....................................................................... 220
8.23. G90 – Set Distance Mode To Absolute
...................................................................... 221
8.24. G91 – Set Distance Mode To Incremental
................................................................. 222
8.25. G92 – Temporary Work Offset
.................................................................................. 223
8.26. G92.1 – Cancel Temporary Work Offset
.................................................................... 224
8.27. G93 – Inverse Time Mode
........................................................................................ 225
8.28. G94 – Units Per Minute Mode
................................................................................... 226
8.29. G95 - Feed Per Revolution
....................................................................................... 227
8.30. G96 – Turn on Constant Surface Speed (CSS)
.......................................................... 228
8.31. G97 – Turn off Constant Surface Speed (CSS)
.......................................................... 229
8.32. G98 – Canned Cycle – Retract Back To The Initial Z
.................................................. 230
8.33. G99 – Canned Cycle – Retract Back To R Plane
....................................................... 231
8.34. MSG - Print message to screen
................................................................................ 232
9. Supported M-codes ..................................................................................................... 235
9.1. M00 – Program Stop
................................................................................................. 236
9.2. M01 – Optional Program Stop
.................................................................................... 237
9.3. M02 – Program End
.................................................................................................. 238
9.4. M03 – Spindle ON (Clockwise)
................................................................................... 239
9.5. M03 – Plasma Torch ON
............................................................................................ 240
9.6. M04 – Spindle ON (Counter Clockwise)
...................................................................... 241
9.7. M05 – Spindle OFF
................................................................................................... 242
9.8. M05 – Plasma Torch OFF
.......................................................................................... 243
9.9. M06 – Tool Change
................................................................................................... 244
9.10. M07 – Turn Mist Coolant On
..................................................................................... 246
9.11. M08 – Turn Flood Coolant On
.................................................................................. 247
9.12. M09 – To Turn All Coolant Off
.................................................................................. 248
9.13. M10 – Chuck Or Rotary Table Clamp On
.................................................................. 249
9.14. M11 – Chuck Or Rotary Table Clamp Off
.................................................................. 250
9.15. M30 – End The Program And Rewind
....................................................................... 251
9.16. M62 – Turn On Digital Output Synchronized With Motion
............................................ 252
9.17. M63 – Turn Off Digital Output Synchronized With Motion
............................................ 253
9.18. M64 – Turn On Digital Output Immediately
................................................................ 254
9.19. M65 – Turn Off Digital Output Immediately
................................................................ 255
9.20. M666 – Plasma – Turn THC Function Off
.................................................................. 256
9.21. M667 – Plasma – Turn THC Function On
.................................................................. 257
9.22. M98 & M99 – Sub Program Call
............................................................................... 258
10. CAM Post Processors ............................................................................................... 260
10.1. Plasma POST Processor Requirements
.................................................................... 261
10.2. Artcam
.................................................................................................................... 263
10.3. BobCAD-CAM
......................................................................................................... 264
10.4. Fusion 360
.............................................................................................................. 266
10.5. SheetCAM
.............................................................................................................. 267
10.6. Vectric VCarve and Vectric Aspire
............................................................................ 268
11. Setup and Calibration ............................................................................................... 269
v5.18 - 08 Apr,2021
www.masso.com.au Page 5 of 477

MASSO G3 Specifications

General

Storage	8GB eMMC
Connectivity	Ethernet, USB
Power Supply	24V DC
Isolated Inputs	16
Isolated Outputs	8
Relay Outputs	2
Encoder Inputs	4
Step/Direction Outputs	6
Analog Inputs	2
Digital Inputs	16
Digital Outputs	8
Humidity	10% to 90% non-condensing
Display	7-inch touchscreen
Axes	Up to 6 axes
Spindle Control	PWM, Analog, or Step/Direction
Software	MASSO OS
Operating Temperature	0°C to 50°C
Storage Temperature	-20°C to 70°C
Memory	1GB RAM
Output Current	500 mA per output