MASSO G3 User Manual

MASSO
MASSO Documentation
11.20. Installing or Replacing Backup Battery
.................................................................... 350
11.21. User Account Settings
............................................................................................ 351
11.22. MASSO Homing Sensor
......................................................................................... 352
11.23. MASSO Optical Encoder
........................................................................................ 354
11.24. MASSO Relay Module
........................................................................................... 356
11.25. MASSO G2 Drive and Relay wiring
......................................................................... 362
11.26. Lubrication
............................................................................................................ 371
11.27. MASSO G2 Replacing Damaged Optocouplers
........................................................ 372
11.28. MASSO G3 Replacing Damaged Optocouplers
........................................................ 377
11.29. Spindle RPM Encoder
............................................................................................ 381
11.29.1. Upgrading the Spindle encoder on MASSO G2
......................................................... 384
12. Save & Load Settings ............................................................................................... 386
13. Touch Probe .............................................................................................................. 389
14. Tool Setter / Touch Plate .......................................................................................... 393
14.1. How Tool Setter Works
............................................................................................ 395
15. Automatic Tool Length Calibration ......................................................................... 398
16. Tool Changers ........................................................................................................... 400
16.1. Mill Tool Changers
.................................................................................................. 401
16.1.1. Manual Tool Changer
........................................................................................... 402
16.1.2. Linear Tool Changer (Type 1)
................................................................................. 404
16.1.3. Linear Tool Changer (Type 2)
................................................................................. 407
16.1.4. Linear Tool Changer configuration
........................................................................... 411
16.1.5. Umbrella Tool Changer
......................................................................................... 421
16.2. Lathe Tool Changers
............................................................................................... 425
16.2.1. Manual Tool Change
............................................................................................ 426
16.2.2. Linear - Gang Type Setup
...................................................................................... 427
16.2.3. 4 Station Turret
.................................................................................................... 428
16.2.4. EMCO PC55 Turn
................................................................................................ 431
16.2.5. 4 Bit Digital Signal Output Turret
............................................................................. 433
16.2.6. Hercus PC200 - 8 Tool Turret
................................................................................. 436
16.2.7. Pragati BTP-63, BTP-80, BTP-100, BTP-125
............................................................. 438
16.2.8. EMCOturn 120
.................................................................................................... 440
16.2.9. WABECO 8 Tool Turret
......................................................................................... 443
17. Plasma - Torch Height Control ................................................................................ 445
17.1. Proma Compact THC 150
........................................................................................ 446
17.2. Hypertherm 45, 65 & 85
........................................................................................... 448
17.3. Torch Touch (floating head) Signal
........................................................................... 449
17.4. Torch Breakaway Signal
.......................................................................................... 451
17.5. How THC works
...................................................................................................... 452
18. OEM Logo & Details .................................................................................................. 460
19. Sherline Mills and Lathes ......................................................................................... 462
19.1. Wiring & Setup
........................................................................................................ 464
20. 3DTEK Routers .......................................................................................................... 466
21. CANCAM Routers ...................................................................................................... 467
22. REVO CNC ................................................................................................................. 468
v5.18 - 08 Apr,2021
www.masso.com.au Page 7 of 477

MASSO G3 Specifications

General

Storage	8GB eMMC
Connectivity	Ethernet, USB
Power Supply	24V DC
Isolated Inputs	16
Isolated Outputs	8
Relay Outputs	2
Encoder Inputs	4
Step/Direction Outputs	6
Analog Inputs	2
Digital Inputs	16
Digital Outputs	8
Humidity	10% to 90% non-condensing
Display	7-inch touchscreen
Axes	Up to 6 axes
Spindle Control	PWM, Analog, or Step/Direction
Software	MASSO OS
Operating Temperature	0°C to 50°C
Storage Temperature	-20°C to 70°C
Memory	1GB RAM
Output Current	500 mA per output