MIMAKI UJF-3042 MkII - Nozzle Recovery Function

Chapter 4 Maintenance
4-13
1
2
2
4
5
6
Nozzle Recovery Function
NOZZLE RECOVERY: When nozzles missing can not be
improved at specific points, other good nozzles can be
used as alternatives for printing.
1
Press the
(MENU)
in LOCAL.
2
Press to select “ MAINTENANCE ”,
and press the key.
• MAINTENANCE MENU will be displayed.
3
Press to select “RECOVERY”,
and press the key.
4
Press to select “PRINT” and
press the key twice.
• Printing of the nozzle pattern will start.
• Select “ENTRY” then “Move to select of the
Nozzle line (Step 4) without drawing a pattern”
5
Press to select “Entry” and
press the key twice.
6
Select the Nozzle line that needs NOZZLE
RECOVERY by pressing , and
press key.
7
Register the Nozzle number that needs
NOZZLE RECOVERY and press
key.
(1) Select the registration number from 1 to 10
by pressing [][] key and press the
[ENTER] key.
(2) Register the nozzle number that needs
recovery by pressing [][] key and press
the [ENTER] key.
8
Press the key several times
to end the setting.
1
8
17
24
33
40
49
56
65
72
81
88
97
104
113
120
129
136
145
152
161
168
177
184
193
200
209
216
225
232
241
248
257
264
273
280
289
296
305
312
1
8
17
24
33
40
49
56
65
72
81
88
97
104
113
120
129
136
145
152
161
168
177
184
193
200
209
216
225
232
241
248
257
264
273
280
289
296
305
312
1
8
17
24
33
40
49
56
65
72
81
88
97
104
113
120
129
136
145
152
161
168
177
184
193
200
209
216
225
232
241
248
257
264
273
280
289
296
305
312
1
8
17
24
33
40
49
56
65
72
81
88
97
104
113
120
129
136
145
152
161
168
177
184
193
200
209
216
225
232
241
248
257
264
273
280
289
296
305
312
1
8
17
24
33
40
49
56
65
72
81
88
97
104
113
120
129
136
145
152
161
168
177
184
193
200
209
216
225
232
241
248
257
264
273
280
289
296
305
312
1
8
17
24
33
40
49
56
65
72
81
88
97
104
113
120
129
136
145
152
161
168
177
184
193
200
209
216
225
232
241
248
257
264
273
280
289
296
305
312
1
8
17
24
33
40
49
56
65
72
81
88
97
104
113
120
129
136
145
152
161
168
177
184
193
200
209
216
225
232
241
248
257
264
273
280
289
296
305
312
1
8
17
24
33
40
49
56
65
72
81
88
97
104
113
120
129
136
145
152
161
168
177
184
193
200
209
216
225
232
241
248
257
264
273
280
289
296
305
312
H1-A H1-B H2-A H2-B H3-A H3-B H4-A H4-B
H4
H1 H2 H3
AB
AB AB AB
Overhead view
Nozzle pattern
NOZZLERECOVERY
SELECT:H1-A
Head No.
(H1 to H6)
Nozzle line
(A, B)
• Up to 10 nozzles can be registered per 1 nozzle
line.
• Even if you use this function, time required for
drawing does not change.
• When printing has been done with the lowest path,
nozzle recovery is not reflected.
Perform test printing to confirm.
• If special ink is unclear, print on the clear film to
check.
NOZZLERECOVERY
NG1:OFF
H1-A
FUNCTION
Recovery nozzle No.: 1 to 318, OFF
Registration number : 1 to 10
1
8
17
24
33
40
49
56
65
72
81
88
97
104
113
120
129
136
145
152
161
168
177
184
193
Nozzle missing
No.91
Nozzle number
Nozzle missing
No.167
Registration
number
Recovery
Nozzle No.
State
1 12 Target for nozzle recovery
2 91 Target for nozzle recovery
3 167 Target for nozzle recovery
4 OFF No registration
5 OFF No registration
Example of nozzle to be recovered
Nozzle missing No.12