MIMAKI UJV55-320 - Chapter 3 Extended Functions; About Setup MENU

Chapter 3 Setup
3-2
About Setup MENU
On Setup MENU, you can set the print conditions to match the media you usually use.
MENU
Setup
>
> Maintenance
>
Machine Setup
Nozzle Check
>
>
Information
>><<
Feed Comp.
>
> PropPos. Correct
Adjust
Feed Comp.
>
> PropPos. Correct
Adjust
REMOTEMENU
TEST PRINT /
CLEANING
PRE
30°C/40°C
3200mm
Local <Setup 1>
Setup
● Setup 1
○ Setup 2
○ Setup 3
○ Setup 4
○ Temporary
>><<
Select “SETUP 1 to 4” or “Temporary”,
and then press the key.
Feed Comp.
>
DropPos. Correct
>
>
Qyality
Heater
HOST
Logical Seek
Overprint
>><<
Setup 1 1/3
Feed Comp.
>
DropPos. Correct
>
>
Qyality
Heater
HOST
Logical Seek
Overprint
>><<
Setup 1 1/3
REMOTEMENU
TEST PRINT /
CLEANING
PRE
30°C/40°C
3200mm
Local <Setup 1>
Margin/L
0mm
Margin/R
0mm
>
Lv.3
UV Mode
Standard
Refresh
Vacuum Fan
>><<
Setup 1 2/3
Print Speed
>
MAPS4
>
>
OFF
Auto Cleaning
Interval Wiping
>><<
Setup 1 3/3
Feed Comp.
>
DropPos. Correct
>
>
Qyality
Heater
HOST
Logical Seek
Overprint
>><<
Setup 1 1/3
Margin/L
0mm
Margin/R
0mm
>
Lv.3
UV Mode
Standard
Refresh
Vacuum Fan
>><<
Setup 1 2/3
Print Speed
>
MAPS4
>
>
OFF
Auto Cleaning
Interval Wiping
>><<
Setup 1 3/3
Feed Comp.
>
DropPos. Correct
>
>
Qyality
Heater
HOST
Logical Seek
Overprint
>><<
Setup 1 1/3
Margin/L
0mm
Margin/R
0mm
>
Lv.3
UV Mode
Standard
Refresh
Vacuum Fan
>><<
Setup 1 2/3
Print Speed
>
MAPS4
>
>
OFF
Auto Cleaning
Interval Wiping
>><<
Setup 1 3/3
Feed Comp.
>
DropPos. Correct
>
>
Qyality
Heater
HOST
Logical Seek
Overprint
>><<
Setup 1 1/3
Margin/L
0mm
Margin/R
0mm
>
Lv.3
UV Mode
Standard
Refresh
Vacuum Fan
>><<
Setup 1 2/3
Feed Comp.
>
DropPos. Correct
>
>
Qyality
Heater
HOST
Logical Seek
Overprint
>><<
Setup 1 1/3
Margin/L
0mm
Margin/R
0mm
>
Lv.3
UV Mode
Standard
Refresh
Vacuum Fan
>><<
Setup 1 2/3
Print Speed
>
MAPS4
>
>
OFF
Auto Cleaning
Interval Wiping
>><<
Setup 1 3/3
Print Speed
>
MAPS4
>
>
OFF
Auto Cleaning
> Setup Reset > Setup Reset > Setup Reset > Setup Reset > Setup Reset
Interval Wiping
>><<
Setup 1 3/3
REMOTEMENU
TEST PRINT /
CLEANING
PRE
30°C/40°C
3200mm
Local <Setup 1>
 Screen transition when (ADJUST) key is pressed
When adjustment functions (Feed Comp./ X-Distance Comp./ Prop Pos. Correct) are performed, the ADJUST
MENU can be displayed easily without selecting [MENU]-[Setup] from Local.
Press the [SEL] key to display “ADJUST” for [FUNC1], and then press the [FUNC1] key.
: Press this to select SETTING MENU, or to switch to the
previous screen.
: Press this to use the adjust function.
: Press this to switch to the next screen.
: Use these to select a setting item.
: Press this to confirm a setting, etc..
 SETUP MENUs at-a-glance