What does Printer Data Loss Trouble mean on Mircom FX-2000?
The 'Printer Data Loss Trouble' message on your Mircom Control Panel appears when a printer is configured but not physically connected to the panel, and a message is sent to the printer. Press the System Reset button to clear this trouble.
Why does my Mircom Control Panel show Slave (RAX-LCDs) Configuration Version Mismatch Trouble?
The 'Slave (RAX-LCDs) Configuration Version Mismatch Trouble' message on your Mircom Control Panel indicates that the firmware versions on all the CPUs are not compatible. Ensure that the firmware versions are compatible.
What does Program Version Mismatch mean on Mircom FX-2000 Control Panel?
The 'Program Version Mismatch' message on your Mircom Control Panel (displayed on the RAX-LCD only) indicates that the RAX-LCD firmware version is not compatible with the FX-2000 firmware version. Make sure that the RAX-LCD firmware version is compatible with the FX-2000 firmware version.
What to do for Configuration Data Error (RAM) on Mircom FX-2000?
The 'Configuration Data Error (RAM)' message on your Mircom Control Panel indicates that the system is overloaded and risks resetting itself. Reload the Configurator and/or reboot the system by powering it down and then powering it up.
What does Configuration Data Error (FLASH) mean for Mircom FX-2000?
The 'Configuration Data Error (FLASH)' message on your Mircom Control Panel indicates that the system is overloaded and risks resetting itself. If this error occurs, report it to Mircom’s Technical Support Department.
General| Type | Fire Alarm Control Panel |
|---|---|
| Display | LCD |
| Network | Optional |
| Communication | RS-232, RS-485 |
| Programming | Via keypad or PC |
| SLC Loops | 1 |
| NAC Outputs | 4 |
| Communication (Additional) | Optional Ethernet |
| Input Voltage | 120 VAC or 240 VAC, 50/60 Hz |
| Battery Charging Current | 1.5 A |
| Auxiliary Power Output | 24 VDC |
| Operating Temperature | 0°C to 49°C (32°F to 120°F) |
| Relative Humidity | Up to 93% non-condensing |
Defines "circuit" and "zone" for FX-2000 system interfaces and protected areas.
Explains Class A, Class B, Style 4, 6, 7 wiring for initiating, NAC, and addressable loops.
Describes the FX-2000 FACP, its analog loop controller, and supported modules.
Lists key features and capabilities of the FX-2000 system, including capacity and modular design.
Describes various adder modules used with the FX-2000 system, such as loop controllers and circuit modules.
Details auxiliary modules like PR-300 and UDACT-300A for specific functions.
Lists and describes the different enclosures available for FX-2000 systems, including dimensions.
Lists and describes remote annunciator panels for the FX-2000, including graphical and text-based models.
Provides diagrams for mechanical installation of various enclosure types.
Provides general instructions for mounting the main chassis into different enclosures.
Shows module mounting locations for FX-2003 series compact main chassis.
Shows module mounting locations for FX-2017 mid-size main chassis.
Shows module mounting locations for FX-2009 large main chassis.
Describes how to mount boards and modules to the BBX-1024XT chassis.
Details settings, jumpers, and connectors for the main fire alarm module.
Details settings, jumpers, and connectors for the Super Main Module.
Details operation and settings for Fan Damper Control modules.
Details jumpers and connections for the DM-1008A hardwire detection adder module.
Details components, jumpers, and connections for SGM-1004A NAC module.
Details connections and jumpers for the RM-1008A hardwire relay adder module.
Details connections, jumpers, and wiring for the PR-300 module.
Details jumpers, LEDs, and cable connectors for the UDACT-300A main board.
Details power, RS-485, DIP switches, and jumpers for the ALC-198S module.
Details power, RS-485, DIP switches, and jumpers for the ALC-396S module.
Details power, RS-485, jumpers, and connectors for the ALC-H16 module.
Shows terminal connections for the main fire alarm module and its various outputs.
Explains analog loop wiring configurations, including Class B, Style 7, and Style 6.
Shows terminal connections for the DM-1008A hardwire detection module.
Shows terminal connections for the SGM-1004A NAC signal module.
Details power supply connections, ratings, and battery fuse information.
Lists pre-power on checks for the FX-2000 system, including wiring and connections.
Step-by-step procedure for powering up the FX-2000 system correctly.
Lists common system messages like Circuit Trouble, Ground Fault, and Battery Trouble.
Lists and describes common indicators on the panel, such as LEDs for AC On, Alarm, Trouble.
Details common controls on the panel, including ACK buttons, cursor buttons, and function buttons.
Explains the function of ACK buttons used to acknowledge alarm, supervisory, and trouble queues.
Describes how the system operates in a single stage alarm mode.
Describes how the system operates in a two stage alarm mode.
Details different types of initiating circuits like Non-Verified Alarm and Water-Flow Alarm.
Details different types of NAC circuits, including Silenceable, Non-Silenceable, Coded, and Strobe.
Explains evacuation codes and patterns like Continuous, Temporal, March, and California Code.
Lists detailed specifications for FX-2003-6DS and FX-2003-6DS-16LED chassis.
Lists detailed specifications for FX-2003-12DS/XTDS and FX-2009 series chassis.
Lists detailed specifications for FX-2017-12ADS and FX-2017S-12ADS chassis.
Lists specifications for various FX-2000 system modules and annunciators.
Lists UL compatible addressable loop devices for the FX-2000 series.
Lists UL compatible two-wire smoke detectors for the FX-2000 series.
Lists UL compatible four-wire smoke detectors for the FX-2000 series.
Lists UL compatible signalling devices for the FX-2000 series.
Lists ULC compatible addressable loop devices for the FX-2000 series.
Lists ULC compatible hardwire smoke detectors for the FX-2000 series.
Table of power requirements for FX-2000 system components.
Formula and guidance for calculating battery capacity based on standby and alarm currents.
Details RA-1000 and RAM-200 series remote annunciators and their models.
Describes the RAX-LCD remote shared display and its features.
DIP switch settings summary for RA-1000 series devices.
DIP switch settings summary for the MGD-32 device.
DIP switch settings summary for the RAX-LCD device.
Details alarm verification timing specific to the ALC-396S module.
Wiring diagram for addressable supervised output modules per UL 864 standard.
Discusses potential reasons for system failures.
Emphasizes the importance of proper installation according to codes.
Highlights the need for regular system testing and maintenance.
Explains issues related to power interruptions and their impact.
Discusses potential battery failures and requirements for system operation.
Details the terms of the limited warranty for MGC products.
Lists conditions that can void the product warranty.
Outlines the steps for obtaining warranty service for products.
Describes the process for obtaining repairs for out-of-warranty products.
Provides a legal disclaimer regarding product warranties.
To Next Page
