EasyManuals Logo

Motorola R-2001D User Manual

Motorola R-2001D
101 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #41 background imageLoading...
Page #41 background image
023071
134223306411
503631
734
025
072
143
226
311
412
506
632 743
026
073
152
243
315
413
516 654 754
031
074
155
244
331
423 532 662
032
114 156
245
343
431
546 664
043
115 162
251
346
432
565
703
047116165261351445606712
051
125
172
263
364 464 612
723
054
131
174
265
365
465
624
731
065
132
205
271
371
466
627
732
TABLE
3-6. VALID
DPL
CODES
AlB
ENCODE
Figure 3-24 shows a display for page I
of
the menu.
To
select sequence input, enter a number from I to 4. Enter
Tone A and Tone B frequencies. Each frequency has a
maximum value
of
20,000 Hz with a resolution
of
0.1
Hz. The system responds to changes in the tone fre-
quency to allow the next complete signaling sequence to
be executed with the new tone frequency. The majority
of
two-tone pagers use the first two fixed sequences
listed in the tone sequence table. The operator cannot
change the first two sequences but he can change the last
two. Each delay entry has a maximum value
of
10
seconds. The system responds to new entries during an
active sequence to allow the next complete signaling se-
quence to be executed with the new timing mformation.
For
triggered sweep on the oscilloscope program the
scope trigger delay to a maximum 10 seconds (0.001
second resolution).
If
time entered exceeds Tone Se-
quence time, the oscilloscope
will
not trigger. Enter
000.0 to disable trigger delay.
SIGNALING SEQUENCE
MODE
SEL) 5
0)
MENU
1)
START
2)
END
DPL
DECODE
DPL
CODE:
321
- NO
INPUT
SIGNAL -
FIGURE
3-23.
DPL
DECODE
DISPLAY
TWO-TONE
SEQUENTIAL
PAGING
Program a two-tone pager access sequence with Tone A
and Tone B frequencies, tone durations, and time be-
tween tones as defined in figure 3-24. Select Tone Se-
quence mode for the code synthesizer,
AlB
sequence
all
the Signaling Sequence DISPLAY, and Generate
FUNCTION. The timing format for this mode consists
of
Tone A for the programmed time, followed by the
programmed delay, followed, by Tone B for the pro-
grammed time, followed by the second programmed
delay. This sequence will repeat in continuous position
but
generate only a single sequence
in
burst position.
SIGNALING SEQUENCE
MODE
SEL) 2
ENTER 0
FOR
MENU
DPL
DECODE
Figure
3-23
shows a display
of
a detected valid code on
page
5.
If
the system detects
an
invalid code, dashes re-
place the code number. Table 3-6 lists the valid
DPL
codes.
5/6
TONE
ENCODE
1)
5-TONE SEQ
SEQ SEL) 2
2)
6-TONE SEQ
SIGNALING SEQUENCE MODE SEL) 1
ENTER
0
FOR
MENU
SCOPE
TRIG DL
Y)
0.000 SEC
FIGURE
3-24.
TWO
TONE
(AlB)
ENCODE
DISPLAY
AlB
ENCODE
A) 01200.0
Hz
SEQ SEL) 1
B) 00300.0
Hz
CAP
CODE) 2-13340X
SCOPE
TRIG
DL
Y)
0.000 SEC
FIGURE
3-25.
5/6
TONE
ENCODE
DISPLAY
5/6
TONE
ENCODE
Figure 3-25 shows an encode display for page 2
of
the
menu. Select either 5-tone
or
6-tone paging. Table
3-7
lists the cap code digits and their frequencies. Enter the
cap code digit for the desired
output
sequence. The code
has a preamble tone number followed by a 5-digit se-
quence number. An X automatically appears at the end
of
the cap code. The system responds to changes in the
cap code to allow the next complete signaling sequence
to
be executed with the new code information. The sixth
or
X tone may not be transmitted by selecting the 5-tone
sequence.
If
the tone
is
not transmitted, a delay equal to
the normal tone X time
is
inserted. With the MODULA-
TION switch in continuous position, the
output
consists
of
the preamble tone followed by a continuous cycling 5
or
6 tone sequence. Cycling terminates only when the
switch
is
moved to the
off
position
or
the mode
is
3-13
(SEC)
TONE
TN&VCE
DLY
1.00
1.30
0.10
0.20
B
0.20
3.00
0.10
0.20
DLY
0.00
0.00
0.10
0.20
A
1)
0040
2)
1.00
3)
0.10
4)
0.20

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Motorola R-2001D and is the answer not in the manual?

Motorola R-2001D Specifications

General IconGeneral
BrandMotorola
ModelR-2001D
CategoryMeasuring Instruments
LanguageEnglish

Related product manuals