NEC Univerge SV8100 - Page 1099

UNIVERGE SV8100 Issue 1.0
SV8100 Features and Specifications Manual 2 - 1075
34-01-01 E&M Tie Line Basic Setup – DID/
E&M Start Signaling
For each ANI/DNIS trunk, set the
start signaling mode to 1 (wink
start).
0 = 2nd Dial Tone
1 = Wink (default)
2 = Immediate
3 = Delay
(default = 2)
3
34-01-02 E&M Tie Line Basic Setup –
Receive Dial Type for E&M Tie
Line
For DID and tie trunks, use this
option to set the trunk signaling
type (Dial Pulse or DTMF)
Related Programming
10-09
0 = DP
1 = DTMF
(default = 1)
3
34-01-03 E&M Tie Line Basic Setup – E&M
Dial-In Mode
Determine if the incoming Tie Line
call should be directed as an
intercom call (0) or if it should
follow the DID Translation Table in
Program 22-11 (1).
0 = Specify Extension
Number (Intercom)
1 = Use Conversion
Table (NTT)
(default = 0)
3
34-01-04 E&M Tie Line Basic Setup – E&M
Line Dial Tone
Enter 1 if the Tie Line should send
dial tone to the calling system after
the call is set up. Enter 0 if the Tie
Line should not send dial tone.
0 = Disable (No)
1 = Enable (Yes)
(default = 1)
3
34-02-01 E&M Tie Line Class of Service Assign a Class of Service (1~15) to
a Tie Line. The Class of Service
options are defined in Program
20-14. For each Tie Line, you
make a separate entry for each
Night Service mode.
Day/Night Mode
1~8
Class: 1~15
(default = 1)
3
34-09-01 ANI/DNIS Service Options –
Receive Format
Use this option to specify the
format of the ANI/DNIS data
received from the Telco. Make sure
your entry is compatible with the
service the Telco provides (4 =
ANIDNIS [ = Delimiter
Code]).
 If PRG34-01-02 is selected to
2 (MF), this PRG works only
as 4 =

ANI

DNIS

0 = Address
1 = ANI
2 = DNIS
3 = ANIAddress
4 = ANIDNIS
5 = DNISANI
( = Delimiter Code)
(default = 0 for
COS 1~15)
3
34-09-02 ANI/DNIS Service Options –
Delimiter Dial Code
This option defines the character
Telco uses as a delimiter (see
entries 1~5 in Program 34-09-01).
Valid entries are: 0~9,
#, and .
1~9, 0, , #
(default =  for
COS 1~15)
3
34-09-03 ANI/DNIS Service Options –
Route Setup of Receive Dial
This option specifies the source of
the data the system uses to route
incoming ANI/DNIS calls. If option
‘2’ is selected, refer to Program 34-
09-04:
0 = Fixed Route (Item 08)
1 = Routes on Received DNIS or
Address Data
2 = Routes on Received ANI Data
0 = Fixed Route (Item 08)
(No Routing)
1 = Routes on Received
DNIS or Address Data
2 = Routes on Received
ANI Data
(default = 0 for
COS 1~15)
3
Program
Number
Program Name Description/Comments Assigned Data
Level
1 2 3