NEC Univerge SV8100 - Page 960

Issue 1.0 UNIVERGE SV8100
2 - 936 Single Line Telephones
15-03-05 Single Line Telephone Basic Data
Setup – Trunk Polarity Reverse
-- Not Used in U.S. --Do Not
Change Default Entry as DTMF
issues may arise with voice mail.
0 = Off
1 = On
(default = 0)
3
15-03-06 Single Line Telephone Basic Data
Setup – Extension Polarity
Reverse
-- Not Used in U.S. -- Do Not
Change Default Entry as DTMF
issues may arise with voice mail.
0 = Disable (Off)
1 = Enable (On)
(default = 0)
3
15-03-07 Single Line Telephone Basic Data
Setup – Enabled On-Hook When
Holding (SLT)
Used to Enable or Disable Enabled
On-Hook When Holding for SLT
terminals.
0 = No
1 = Yes
(default = 1)
3
15-03-08 Single Line Telephone Basic Data
Setup – Answer On-Hook when
Holding (SLT)
Used to Enable or Disable Answer
ON-Hook when Holding for SLT
terminals.
0 = Disable
(No)
1 = Yes
(Enable)
(default = 1)
3
15-03-09 Single Line Telephone Basic Data
Setup – Caller ID Function - For
External Module
Enable (1) or disable (0) the Caller
ID FSK signal for an external Caller
ID module or a 3rd party vendor
telephone with Caller ID display.
Important:
If voice mail is used, this setting
must be disabled for the system
integration codes to be correct.
With a 2500 set (no Caller ID)
installed, this must be set to 0 for
incoming callers to have a talk path.
0 = Disable
1 = Enable
(default = 0)
3
15-03-10 Single Line Telephone Basic Data
Setup – Caller ID Name
Determine if an extension user
telephone should display the Caller
ID name.
0 = Disable
1 = Enable
(default = 1)
3
15-03-11 Single Line Telephone Basic Data
Setup – Caller ID Type
Determine whether the Caller ID
type is FSK or DTMF.
0 = FSK
1 = DTMF
(default = 0)
3
15-03-14 Single Line Telephone Basic Data
Setup – Forwarded Caller ID
Display Mode
Determine what the display shows
when a multiline terminal receives a
forwarded outside call.
0 = Calling Extension
Number (Calling)
1 = External Caller ID
(Forward)
(default = 0)
3
20-03-01 System Options for Single Line
Telephones – SLT Call Waiting
Answer Mode
For a busy single line (500/2500
type) telephone, set the mode used
to answer a camped-on trunk call.
For ESL sets, enabling this option
(1) allows the user to dial Service
Code for Voice Mail Conversation
Record.
0 = Hookflash (Hooking)
1 = Hookflash + Service
Code 654
(default = 0)
3
20-03-02 System Options for Single Line
Telephones – Ignore Received DP
Dial on DTMF SLT Port
Use this option to define whether
the system should receive dial pulse
and DTMF signals (0) or ignore dial
pulse and only accept DTMF signals
(1).
0 = Do not ignore (No)
1 = Ignore (Yes)
(default = 0)
3
20-03-03 System Options for Single Line
Telephones – SLT DTMF Dial to
Trunk Lines
Set the SLT phones to (0). Collect
all digits before sending or (1), send
out immediately after receiving.
When using a third-party external
paging device, set this option to 1.
In addition, set Program 20-03-04 to
1.
0 = Receive all digits, before
sending (All)
1 = Direct through out
(Direct)
(default = 0)
3
20-03-04 System Options for Single Line
Telephones – Dial Sending Start
Time for SLT or ARS
Set the time before the first digit is
sent out. When using a third-party
external paging device, set this
option to 1. In addition, set Program
20-03-03 to 1.
0~64800 (seconds)
(default = 1 second)
3
Program
Number
Program Name Description/Comments Assigned Data
Level
1 2 3