Nibe FIGHTER 360P - Max Phase Current; Connecting the Outside Sensor; Access to the Lower Electrical Connections

Electrical connection
FIGHTER 360P
For the Installer
16
12
3
4
56
7
8
15
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
4
X4.1
4
X4.1
X6.1
4
X4.1
4
X4.1
Matning
Max 2A/250 VA C
Utgång
Högprioriterat larm
Matning
Max 2A/250 VA C
Utgång
Lågprioriterat larm
X1
1
5
10
15
X2
X3
83
93
89
X5.1
5
10
15
20
94
88
92
86
87
33
41
2
14
X6.1
X6.1
X6.1
15
(3)
(1)
1
2
3
1
2
3
Connecting the outside sensor
Install the outside sensor in the shade on a wall facing
north or north-west, so it is unaffected by the morning
sun. The sensor is connected with two-wire cable to
terminal block (14) positions 1 and 2, on the load mon-
itor card (2).
If a conduit is used it must be sealed to prevent con-
densation in the sensor capsule. The minimum cable
cross section should be 0.4 mm
2
up to lengths of 50
metres, for example, EKKX or LiYY.
Access to the lower electrical connections
Open the centre front cover by removing the four
screws. The load monitor card (2), microprocessor
card (34), etc are now accessible on the left-hand side.
Remove the protection plate by loosening the four
screws to gain access to the right-hand side.
NOTE!
Electrical installation and service
must be carried out under the
supervision of a qualified electrician
in accordance with the stipulations in
force.
LEK LEK
2
1
bar
3
0 4
2
1
bar
3
0 4
LEK
2
1
bar
3
04
T G
+2
0
-2
1
R
0
ÅTERSTÄLLNING AV SÄKRING
SÄKERHETSVENTIL, VÄRMESYSTEM:
TRYCK (PANNA/VÄRMESYSTEM):
0 AVSTÄNGD
1 NORMALLÄGE
2 RESERVLÄGE
REGELBUNDET UNDERHÅLL/KONTROLL AV:
LUFTFILTER
FLÄKT
VENTILATION
SÄKERHETSVENTILER
VENTILER
STRÖMSTÄLLARE
k.v.
v.v.
k.v.
v.v.
NOTE!
Electrical installation and service must
be carried out under the supervision of
a qualified electrician in accordance
with the stipulations in force.
The temperature limiter (6) is accessible from behind
the centre front cover and is positioned under the inner
protective cover.
The temperature limiter is reset by firmly pressing in
its button. The button can be accessed from the under-
side of the distribution box. The cover on the distribu-
tion box does not need to be removed when resetting.
Resetting the
temperature limiter
LEK LEK
Art.nr. 611827
2
1
bar
3
0 4
Art.nr. 611827
2
1
bar
3
0 4
LEK
2
1
bar
3
0 4
T G
+2
0
-2
1
R
0
ÅTERSTÄLLNING AV SÄKRING
SÄKERHETSVENTIL, VÄRMESYSTEM:
TRYCK (PANNA/VÄRMESYSTEM):
0 AVSTÄNGD
1 NORMALLÄGE
2 RESERVLÄGE
REGELBUNDET UNDERHÅLL/KONTROLL AV:
LUFTFILTER
FLÄKT
VENTILATION
SÄKERHETSVENTILER
VENTILER
STRÖMSTÄLLARE
k.v.
v.v.
Blaha blaha
och annat
trams
Blaha blaha
och annat
trams
k.v.
v.v.
Blaha blaha
och annat
trams
Blaha blaha
och annat
trams
6