Nibe FIGHTER 360P - External Contacts

Electrical connection
FIGHTER 360P
18
For the Installer
Contact for changing the room tempera-
ture
An external contact function can be connected to
FIGHTER 360P to change the supply temperature and
in doing so change the room temperature, for example,
a room thermostat or a timer. The contact should be
potential free and is connected between terminals 3 and
4 on terminal block (14) on the load monitor card (2).
When the contact is made the supply temperature is
higher or lower than the selected curve slope. The val-
ue for the change is set on menu 2.5, External adjust-
ment. The value is adjustable between -5 and +5. One
step corresponds to one step of the heating curve off-
set.
Contact for activation of Extra hot water
An external contact function can be connected to FIGHT-
ER 360P for activation of the Temporary Extra hot water
function. The contact should be potential free and non-
locking and is connected via the edge board connector
between positions 1 and 2 down on the lower part of the
left connection row on the load monitor card (2).
When the contact makes for at least one second the Tem-
porary Extra hot water function is activated. An automatic
return to the previously set function occurs after 24 hours.
This connection requires the accessory XTS 20.
Contact for activation of Fan speed II
An external contact function can be connected to
FIGHTER 360P for activation of fan speed II. The con-
tact should be potential free and non-locking and is
connected via the edge board connector between posi-
tions 3 and 4 down on the lower part of the left connec-
tion row on the load monitor card (2). When the contact
makes for at least one second Fan speed II is activated.
The return to normal speed occurs according to the
time set in menu 7.11, Return-time speed II. This con-
nection requires the accessory XTS 20.
External contacts
12
3
4
56
7
8
15
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
4
X4.1
4
X4.1
X6.1
4
X4.1
4
X4.1
Matning
Max 2A/250 VA C
Utgång
Högprioriterat larm
Matning
Max 2A/250 VA C
Utgång
Lågprioriterat larm
X1
1
5
10
15
X2
X3
83
93
89
X5.1
5
10
15
20
94
88
92
86
87
33
41
2
14
X6.1
X6.1
X6.1
15
(3)
(1)
1
2
3
1
2
3
12
3
4
56
7
8
15
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
4
X4.1
4
X4.1
X6.1
4
X4.1
4
X4.1
Matning
Max 2A/250 VA C
Utgång
Högprioriterat larm
Matning
Max 2A/250 VA C
Utgång
Lågprioriterat larm
X1
1
5
10
15
X2
X3
83
93
89
X5.1
5
10
15
20
94
88
92
86
87
33
41
2
14
X6.1
X6.1
X6.1
15
(3)
(1)
1
2
3
1
2
3
12
3
4
56
7
8
15
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
12
3
4
56
7
8
14
9
10 11
12 13 14 15 16
17
4
X4.1
4
X4.1
X6.1
4
X4.1
4
X4.1
Matning
Max 2A/250 VA C
Utgång
Högprioriterat larm
Matning
Max 2A/250 VA C
Utgång
Lågprioriterat larm
X1
1
5
10
15
X2
X3
83
93
89
X5.1
5
10
15
20
94
88
92
86
87
33
41
2
14
X6.1
X6.1
X6.1
15
(3)
(1)
1
2
3
1
2
3