Nord Drivesystems NORDAC LINK SK250E-FDS - Page 130

NORDAC LINK (SK 250E-FDS ... SK 280E-FDS) – Users Manual for Frequency Inverters as Field Distributors
130 BU 0250 en-3021
Pos: 405 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P400- P499/Parameter P482 – Normier ung Bus I/O Out Bits [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 2\mod_13469 31812166_388.doc x @ 42936 @ @ 1
P482 [-01]
...
[-10]
Standard BusIO Out Bits
(Standardisation of Bus I/O Out Bits)
S
-400 … 400 %
{ all 100 }
Adjustment of the limit values of the bus Out bits. For a negative value, the output function will be
output negative.
Once the
limit value is reached and positive values are delivered, the output produces a High
signal, for negative setting values a Low signal.
[-01] = Bus / AS-i Dig Out1
(Bus IO Out Bit 0 + AS-i 1)
[-02] = Bus / AS-i Dig Out2 (Bus IO Out Bit 1 + AS-i 2)
[-03] = Bus / AS-i Dig Out3
(Bus IO Out Bit 2 + AS-i 3)
[-04] = Bus / AS-i Dig Out4 (Bus IO Out Bit 3 + AS-i 4)
[-05] = Bus / IOE Dig Out1 (Bus IO Out Bit 4 + DO 1 of the first SK xU4-IOE (DigOut 02))
[-06] = Bus / IOE Dig Out2
(Bus IO Out Bit 5 + DO 2 of the first SK xU4-IOE (DigOut 03))
[-07] = Bus / 2nd IOE Dig Out1 (Flag1 + DO 1 of the second SK xU4-IOE (DigOut 04))
[-08] = Bus / 2nd IOE Dig Out2
(Flag2 + DO 2 of the second SK xU4-IOE (DigOut 05))
[-09] = Bit 10 BUS status word
[-10] = Bit 13 BUS status word
Pos: 406 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P400- P499/Parameter P483 – Hyster ese Bus I/O Out Bits [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 2\mod_134693181 2868_388.docx @ 42960 @ @ 1
P483 [-01]
...
[-10]
Hyst. BusIO Out Bits
(Hysteresis of Bus I/O Out Bits)
S
1 … 100 %
{ all 10 }
Difference between switch-on and switch-off point to prevent oscillation of the output signal.
[-01] = Bus / AS-i Dig Out1 (Bus IO Out Bit 0 + AS-i 1)
[-02] = Bus / AS-i Dig Out2
(Bus IO Out Bit 1 + AS-i 2)
[-03] = Bus / AS-i Dig Out3 (Bus IO Out Bit 2 + AS-i 3)
[-04] = Bus / AS-i Dig Out4
(Bus IO Out Bit 3 + AS-i 4)
[-05] = Bus / IOE Dig Out1 (Bus IO Out Bit 4 + DO 1 of the first SK xU4-IOE (DigOut 02))
[-06] = Bus / IOE Dig Out2
(Bus IO Out Bit 5 + DO 2 of the first SK xU4-IOE (DigOut 03))
[-07] = Bus / 2nd IOE Dig Out1 (Flag1 + DO 1 of the second SK xU4-IOE (DigOut 04))
[-08] = Bus / 2nd IOE Dig Out2
(Flag2 + DO 2 of the second SK xU4-IOE (DigOut 05))
[-09] = Bit 10 BUS status word
[-10] = Bit 13 BUS status word
NOTE:
Details for the use of the relevant bus systems can be found in the applicable supplementary bus
manual.
Pos: 407 /Allgemein/A llgemeingültige Module/---------Seitenumbruch kompakt --------- @ 13\mod_14763696959 06_0.docx @ 2265495 @ @ 1