Nord Drivesystems NORDAC LINK SK250E-FDS - Display of Messages; Diagnostic Leds on Device

6 Operating status messages
BU 0250 en-3021 165
Pos: 567 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/D arstellung der Meldungen @ 3\ mod_136180270845 5_388.docx @ 59827 @ 2 @ 1
6.1 Display of messages
Pos: 568 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/D arstellung der Meldungen - LED Anzeigen [SK xxxE- FDS] @ 12\mod_1468482312711_ 388.docx @ 339100 @ 5 @ 1
LED indicators
The device status is indicated by an externally visible “FI status” LED ( Section 3.1 "Displays").
Pos: 569 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/D arstellung der Meldungen - SimpleBox / ControlBox Anzeige [SK xxxE, SK 5xxP] @ 3\mod_1361801795294_38 8.docx @ 59802 @ 5 @ 1
SimpleBox Display
The SimpleBox displays an error with its number and the prefix "E". In addition, the present fault can
be displayed in array element [-01] of parameter (P700). The last error messages are stored in
parameter (P701). Further information about the frequency inverter status at the moment of the fault
can be obtained from parameters (P702) to (P706) / (P799)
If the cause of the error is no longer present, the error display in the SimpleBox flashes and the error
can be acknowledged with the Enter key.
In contrast, warning messages are prefixed with "C" ("Cxxx") and cannot be acknowledged. They
disappear automatically when the reason for them is no longer present or the frequency inverter has
switched to the "Error" state. Display of the message is suppressed if the warning appears during
parameterisation.
The present warning message can be displayed in detail at any time in array element [-02] of
parameter (P700).
The reason for an existing disabled switch on cannot be displayed with the SimpleBox.
Pos: 570 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/D arstellung der Meldungen - ParameterBox - Anzei ge @ 3\mod_1361801566355 _388.docx @ 59779 @ 5 @ 1
ParameterBox display
The ParameterBox displays the messages in plain text.
Pos: 571 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/D iagnose LEDs/Diagnose LED s am Gerät (Überschri ft+) [SK 1xxE, SK 2xxE, SK xxxE-FDS] @ 1\mod_1343201905 326_388.docx @ 36935 @ 2 @ 1
6.2 Diagnostic LEDs on device
The device generates operating status messages. These messages (warnings, errors, switching
statuses, measurement data) can be displayed with parametrisation tools ( Section 3.2 "Control and
parametrisation options ") (Parameter group P7xx).
To a limited extent, the messages are also indicated via the diagnostic and status LEDs.
Pos: 572 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/D iagnose LEDs/Diagnose LED s am Gerät_Ergänzun g [SK 2xxE-FDS] @ 12\mod_146735731 7923_388.docx @ 335830 @ @ 1
Explanations of the LED indicators can be found in  Section 3.1 "Displays".
Pos: 573 /Allgemein/A llgemeingültige Module/---------Seitenumbruch kompakt --------- @ 13\mod_14763696959 06_0.docx @ 2265495 @ @ 1