– 123 –
Chapter 6 Thumbnail Operations for Clips — Thumbnail operations
(Yellow)
Displayed in yellow while the wired LAN is connected.
(Red)
Displayed in red when there is a problem with the connection of wired LAN.
(Gray)
Displayed in gray when the wireless LAN is not activated properly.
(White)
Displayed in white when the wireless LAN is not connected.
(Yellow)
Displayed in yellow while the wireless LAN is connected.
(Red)
Displayed in red when there is a problem with the connection of wireless LAN.
(Gray)
Displayed in gray when the 4G/LTE USB modem is not activated properly.
(White)
Displayed in white when the 4G/LTE USB modem is not connected.
(Yellow)
Displayed in yellow when the 4G/LTE USB modem is connected. Signal strength is represented by yellow vertical bars.
(Red)
Displayed in red when there is a problem with the 4G/LTE USB modem.
(Gray)
Displayed in gray when upload has not started, or upload is complete.
(Yellow)
Displayed in yellow during upload.
(Red)
Displayed from when upload error occurred until when the next transfer starts.
@@
NOTE
t When remote control is possible in an IP connection, “R” is displayed on the network status indicator.
3 Display mode
Displays the types of the thumbnails to be displayed on the screen and the types of other information screens. To switch between displays, refer to
“Thumbnail screen display settings” (page 126).
[ALL] Displays all clips.
[SAME FORMAT] Displays clips in the same format as the system format.
[SELECT] Displays clips selected with the <SET> button.
[MARKER] Displays clips with shot marks.
[TEXT MEMO] Displays clips with text memo data.
[SLOT n] Displays clips in the specied P2 card. (n: indicates slot number 1 to 2.)
[NG CLIPS] Displays defective clips.
[P2/REMAIN] Displays media information (remaining capacity).
[P2/USED] Displays media information (used capacity).
[META DATA] Displays the set metadata.
4 Simple properties display
This displays the various properties of the clip on which the pointer is positioned. You can select the items to display from the menu. For details, refer
to “Properties” (page 134).
@@
NOTE
t If the maximum number of characters is exceeded, it will only display the maximum number of characters that can be displayed.
5 Thumbnail
Displays the thumbnail recorded in each clip. This thumbnail can be changed using the [EXCH. THUMBNAIL] function.
For details, refer to “Thumbnail screen display settings” (page 126).
6 Clip information display
Displays any one of the time code [TC] at the start of clip recording/user bits [UB] at the start of clip recording/shooting time [TIME]/shooting date
[DATE]/shooting date and time [DATE TIME]/clip name [CLIP NAME]/user clip name [USER CLIP NAME]/card slot number [SLOT]/time cord of the
thumbnail [THUMBNAIL TC] according to the setting.
7 Recording mode
Displays the recording mode for the clip on which the cursor is positioned.
8 System format
Displays the format for the clip on which the cursor is positioned.
9 Duration
Displays the clip length (duration) at the cursor position and the current rough playback position against the clip length.
10 Thumbnail information
Displays the thumbnail information (selected number of clips, total playback time of selected clips, or total playback time of displayed clips) set in the
main menu → [CLIP] → [THUMBNAIL SETUP] → [THUMBNAIL INFO.] (page 171).
11 Clip number
The number assigned to the clip on the P2 card is displayed, normally in the order from the earliest recording date and time. The clip numbers of
clips that cannot be played are shown in red, and the unplayable indicator
is also displayed.
For details, refer to “Thumbnail screen display settings” (page 126).
12
Shot mark indicator
Displayed for the clip of a thumbnail with a shot mark attached.
For details, refer to “Shot mark recording function” (page 42).
13
Indicator for clips with proxy
Displayed for clips with proxy attached.
14
Text memo indicator
Displayed for clips with text memo data attached.
To Next Page
Loading...
