Panasonic AJ-PX5000G - Rec;Pb Setup

– 173 –
Chapter 7 Menu Operations — Menu list
[REC/PB SETUP]
Item Description of settings
[REC MEDIA] Selects the slot for the media to be recorded.
[P2]: Uses P2 memory cards (slots 1 and 2).
[microP2]: Uses microP2 memory cards (slots 3 and 4).
f Factory setting: [microP2]
Recording is not possible when a card is inserted into a slot that is not selected.
[FILE SPLIT] Selects the split method of the recording le.
[ONE FILE]: The clip is recorded in one le in the AVC-LongG format to a microP2 memory card
(exceeding 32 GB).
[SPLIT]: The clip is split every 4 GB regardless of the recording format.
[SHORT SPLIT]: The clip is split every 128 seconds regardless of the recording format.
f Factory setting: [SPLIT]
If the clip is recorded in one le, it cannot be copied to a P2 memory card or 32 GB microP2 memory card,
or copied or exported to storage.
When [ONE FILE] is selected, proxy recording is not possible. Also, when the main menu → [REC/PB]
→ [DUAL CODEC SETUP] → [CODEC USAGE] is set to [PROXY REC(P2)] or [PROXY REC(P2&SD)],
[ONE FILE] cannot be selected.
It will be divided to recording les of approximately 128 seconds when [SHORT SPLIT] is selected, but
they can be operated as a single clip when the thumbnail of the clips are operated on the P2 device. A
single continuous recording time is approximately 3.5 hours.
[START TEXT MEMO] Selects the function that automatically adds a text memo at recording start position each time recording is
started.
[ON]: A text memo is added to each recording.
[OFF]: Does not add a text memo.
f Factory setting: [OFF]
Text memos added when this item is [ON] indicate the recording start position. To record text memos as
character information, refer to “Setting clip metadata” (page 131).
This item is disabled when the main menu → [REC/PB] → [REC FUNCTION] → [RECORDING] is set to
an item other than [NORMAL].
[P.ON REC SLOT SEL] Selects the slot order targeted for recording when power is turned on.
[HOLD]: Records from the recording slot used the last time power was turned off.
[SLOT 1/3]: Each time the power is turned on, this changes in order from slot 1 or 3 (slot selected in [REC
MEDIA]) to the recording target card.
f Factory setting: [HOLD]
[REC START] Selects acceptance of the start of recording.
[ALL]: Accepts start of recording during stop, during recording pause, and during playback.
[NORMAL]: Accepts start of recording during stop and during recording pause.
f Factory setting: [NORMAL]
If the main menu → [REC/PB] → [REC FUNCTION] → [RECORDING] is set to an item other than
[NORMAL], operation will be [NORMAL] even when this item is set to [ALL].
[REC TALLY] Selects the method to display recording status at the camera.
[RED]: The red tally lamp illuminates.
[GREEN]: The green tally lamp illuminates.
[CHAR]: The characters “REC” are displayed in the viewnder.
f Factory setting: [RED]
If set [GREEN] or [CHAR], the viewnder front tally lamp, back tally lamp and rear tally lamp do not light
while this camera is recording.
[ACCESS LED] Selects whether to light the access LED of the P2 card.
[ON]: Lights.
[OFF]: Does not light.
f Factory setting: [ON]
[SEEK POS SEL] Selects the position to move when the <FF/REW> button is pressed while playback is paused.
[CLIP]: Top of the clip
[CLIP&TEXT MEMO]: Top of the clip and text memo location
f Factory setting: [CLIP]