Panasonic AJ-PX5000G - Menu List; [Paint]; Rb Gain Control; Rgb Black Control

– 149 –
Chapter 7 Menu Operations — Menu list
Menu list
[PAINT]
These are items for performing ne image adjustments while monitoring the output waveform of the camera using the waveform monitor. You will need
support from video engineers to use congure these settings.
These menu item settings are enabled when using the camera as a standalone device.
These menu items can be set from an external remote controller.
These menu items cannot be set when the thumbnail screen is displayed.
[RB GAIN CONTROL]
Item Description of settings
[R GAIN AWB PRE] Sets the Rch gain when the <WHITE BAL> switch is on <PRST>.
[−200]…[200]
f Factory setting: [0]
[B GAIN AWB PRE] Sets the Bch gain when the <WHITE BAL> switch is on <PRST>.
[−200]…[200]
f Factory setting: [0]
[R GAIN AWB A] Sets the Rch gain when the <WHITE BAL> switch is on <A>.
[−200]…[200]
f Factory setting: [0]
[B GAIN AWB A] Sets the Bch gain when the <WHITE BAL> switch is on <A>.
[−200]…[200]
f Factory setting: [0]
[R GAIN AWB B] Sets the Rch gain when the <WHITE BAL> switch is on <B>.
[−200]…[200]
f Factory setting: [0]
[B GAIN AWB B] Sets the Bch gain when the <WHITE BAL> switch is on <B>.
[−200]…[200]
f Factory setting: [0]
[AWB A GAIN OFFSET] Sets the Rch gain and Bch gain when performing automatic white balance after the <WHITE BAL> switch
is on <A>.
[ON]: Keeps the values set in [R GAIN AWB A] and [B GAIN AWB A].
[OFF]: Sets the value of Rch gain and Bch gain to [0].
f Factory setting: [OFF]
[AWB B GAIN OFFSET] Sets the Rch gain and Bch gain when performing automatic white balance after the <WHITE BAL> switch
is on <B>.
[ON]: Keeps the values set in [R GAIN AWB B] and [B GAIN AWB B].
[OFF]: Sets the value of Rch gain and Bch gain to [0].
f Factory setting: [OFF]
@@
NOTE
t Settings made through the menu are disabled when the remote control unit and extension control unit are connected. (Setting values are displayed.)
[RGB BLACK CONTROL]
Item Description of settings
[MASTER PED] Sets the master pedestal level.
[−200]…[200]
f Factory setting: [16]
[R PEDESTAL] Sets the Rch pedestal level.
[−100]…[100]
f Factory setting: [0]
[G PEDESTAL] Sets the Gch pedestal level.
[−100]…[100]
f Factory setting: [0]
[B PEDESTAL] Sets the Bch pedestal level.
[−100]…[100]
f Factory setting: [0]
[PEDESTAL OFFSET] Sets the Rch, Gch, and Bch pedestal levels after adjusting the automatic black balance.
[ON]: Keeps each of the values set in [R PEDESTAL], [G PEDESTAL], and [B PEDESTAL].
[OFF]: Sets the pedestal level of Rch, Gch, and Bch to [0].
f Factory setting: [OFF]
[R FLARE] Adjusts the Rch are level.
The adjusted value of this item is added to the are adjusted value in the main menu → [MAINTENANCE]
→ [LENS FILE ADJ.].
[−100]…[100]
f Factory setting: [0]
[G FLARE] Adjusts the Gch are level.
The adjusted value of this item is added to the are adjusted value in the main menu → [MAINTENANCE]
→ [LENS FILE ADJ.].
[−100]…[100]
f Factory setting: [0]