– 176 –
Chapter 7 Menu Operations — Menu list
Item Description of settings
[INITIALIZE] Deletes all loaded metadata and initializes.
[PROPERTY] Checks and corrects loaded metadata.
This item is enabled while the thumbnail is displayed.
[LANGUAGE] Sets the language used to display metadata.
[ENGLISH], [JAPANESE]
f Factory setting: [JAPANESE]
This items is displayed when [NTSC (J)] is selected in [OPTION MENU] → [AREA SETTING].
[I/F SETUP]
These are items for setting related to audio and video input/output and display, and setting battery, audio, video output, etc.
[OUTPUT SEL]
Item Description of settings
[OUTPUT ITEM] Sets the character content to superimpose on the output signal of the <SDI OUT1> terminal and monitor
output terminal (<SDI OUT2>, <HDMI OUT>, and <VIDEO OUT>).
[MENU ONLY]: Displays only on the menu. Normally, nothing is displayed.
[TC]: Displays the time code. (Menu is displayed on the menu)
[STATUS]: Displays all items that are the same as the characters displayed on the viewnder. (Menu is
displayed on the menu)
f Factory setting: [MENU ONLY]
The time code display position moves up and down based on the camera ID position.
[SDI OUT1] Turns <SDI OUT1> terminal output [ON]/[OFF].
[ON]: Performs output.
[OFF]: Stops output.
f Factory setting: [ON]
[SDI OUT1 MODE] Selects <SDI OUT1> terminal output signals.
[MEM]: In playback mode, these are playback images.
[CAM]: When the main menu → [SYSTEM] → [SYSTEM MODE] → [REC SIGNAL] is set to [CAM], output
is always camera images.
f Factory setting: [MEM]
[SDI OUT1 CHAR] Selects whether to superimpose characters on <SDI OUT1> terminal output images.
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [OFF]
The content of characters to superimpose is the same as the characters superimposed on images output
from <SDI OUT2> and other terminals.
[SDI OUT2] Turns <SDI OUT2> terminal output [ON]/[OFF].
[ON]: Performs output.
[OFF]: Stops output.
f Factory setting: [OFF]
[VIDEO OUT] Turns <VIDEO OUT> terminal output [ON]/[OFF].
[ON]: Performs output.
[OFF]: Stops output.
f Factory setting: [OFF]
[SDI2/HDMI OUT] Selects the signal form to be output to the monitor output terminal (<SDI OUT2> or <HDMI OUT>) in HD
mode.
[SYSTEM MODE]: Outputs in the system mode signal format.
[DOWNCON]: Outputs the down converter signal.
f Factory setting: [SYSTEM MODE]
[1080P SDI2/HDMI OUT] Selects whether to convert the output signal of the monitor output terminal (<SDI OUT2> or <HDMI OUT>)
to 1080i when in 1080P mode.
[1080P]: Outputs as 1080P.
[1080i]: Converts to 1080i and outputs.
f Factory setting: [1080P]
If the main menu → [I/F SETUP] → [OUTPUT SEL] → [SDI2/HDMI OUT] is set to [DOWNCON], the signal
that was down-converted is output, regardless of these settings.
[3G-SDI OUT] Selects 1080P signals of the HD SDI output in 1080P mode.
[LEVEL-A]: Selects the LEVEL-A method.
[LEVEL-B]: Selects the LEVEL-B DL method.
f Factory setting: [LEVEL-B]
[MONITOR OUT MODE] Selects the output signals of the monitor output terminal (<SDI OUT2>, <HDMI OUT> or <VIDEO OUT2>).
Operates independently of the <SDI OUT1> terminal.
[MEM]: In playback mode, these are playback images.
[CAM]: When the main menu → [SYSTEM] → [SYSTEM MODE] → [REC SIGNAL] is set to [CAM], output
is always camera images.
f Factory setting: [MEM]
[MONITOR OUT ZEBRA] Selects whether the zebra pattern is superimposed over the output video signals from the monitor output
terminals (<SDI OUT2>, <HDMI OUT>, and <VIDEO OUT>). (The remote VBS signal also interlocks.)
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [OFF]
To Next Page
Loading...
