Panasonic AJ-PX5000G - [File]; Setup Data (Sd Card)

– 186 –
Chapter 7 Menu Operations — Menu list
Item Description of settings
[TYPE C FULL]
Selects the voltage for full display in steps of 0.1 V when the main menu → [I/F SETUP] → [BATTERY/
P2CARD] → [BATTERY SELECT] is set to [TYPE C].
[13.0V]…[17.0V]
f Factory setting: [15.9V]
[TYPE C NEAR END]
Selects the near end voltage in steps of 0.1 V when the main menu → [I/F SETUP] → [BATTERY/
P2CARD] → [BATTERY SELECT] is set to [TYPE C].
[11.0V]…[15.0V]
f Factory setting: [13.2V]
[TYPE C END]
Selects the end voltage in steps of 0.1 V when the main menu → [I/F SETUP] → [BATTERY/P2CARD] →
[BATTERY SELECT] is set to [TYPE C].
[11.0V]…[15.0V]
f Factory setting: [12.5V]
[BATT STAT NEAR END] Selects the near end percent value.
[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]
f Factory setting: [5%]
When the battery charge level percentage cannot be detected, this will follow the near end voltage value
set in [TYPE A].
If a battery is used for which the remaining charge is displayed in units of 10%, the setting value and actual
near end warning may vary slightly.
[BATT STAT END] Selects the end percent value.
[1%]…[10%]
f Factory setting: [1%]
When the battery charge level percentage cannot be detected, this will follow the end voltage value set in
[TYPE A].
When using a battery which displays battery charge level by units of 10%, end is determined only in two
stages: when it is set between [1%] and [5%], or when it is set between [6%] to [10%].
[ENDURA STAT NEAR END] Selects the near end percent value.
[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]
f Factory setting: [5%]
When the battery charge level percentage cannot be detected, this will follow the near end voltage value
set in [TYPE A].
If a battery is used for which the remaining charge is displayed in units of 10%, the setting value and actual
near end warning may vary slightly.
[ENDURA STAT END] Selects the end percent value.
[1%]…[10%]
f Factory setting: [1%]
When the battery charge level percentage cannot be detected, this will follow the end voltage value set in
[TYPE A].
When using a battery which displays battery charge level by units of 10%, end is determined only in two
stages: when it is set between [1%] and [5%], or when it is set between [6%] to [10%].
[FILE]
These are items for performing le-related operations such as reading from an SD memory card containing menu settings data, and handling lens les
and lens chromatic aberration correction (CAC) les.
These menu items cannot be set when the thumbnail screen is displayed or during playback.
[FILE] menu cannot be operated in the following cases:
f While the thumbnail screen is displayed
Remedy: Press the <THUMBNAIL> button to close the thumbnail screen, and try the operations again.
f During playback
Remedy: Press the <STOP> button to stop playback, and try the operations again.
f When recording by linking to the previous clip is possible in one-clip recording mode (when [1*CLIP] is displayed at the bottom right in the viewnder
and the LCD monitor)
Remedy: Close the menu once, and hold down the <STOP> button for approx. 2 seconds to end linking of clips, and then try the operation again.
f During standby in interval recording or one-shot recording
Remedy: Press the <STOP> button to end interval recording, and try the operation again.
[SETUP DATA (SD CARD)]
Item Description of settings
[LOAD] Loads the le selected from the setup data le list saved to the SD memory card to the camera.
The data selected in [SETUP DATA SELECT] is loaded.
[SAVE] Overwrites the current menu setting values in the camera to the le selected from the existing le list
saved to the SD memory card.
Data selected in [SETUP DATA SELECT] is saved.
[SAVE AS] Enters the current menu setting values of the camera to le name and title as a new le and saves it to the
SD memory card.
Data selected in [SETUP DATA SELECT] is saved.