Panasonic AJ-PX5000G - Using FTP Client Function; FTP Client Function Setting

– 231 –
Chapter 9 Network Connection — Using FTP client function
Using FTP client function
To use the FTP client function, network conguration and FTP client settings are necessary in advance.
FTP client function setting
By connecting the camera to network using wireless LAN (wireless access point connection),4G/LTE, or wired LAN, you can transfer clips to a server
device on the network.
Client settings
To transfer clips with the FTP client function, you need to set the connection destination and other settings in advance.
1
Set each item in the main menu → [I/F SETUP] → [USB/LAN] → [FTP CLIENT SERVICE].
[SETTING DATA]: Sets from where client service settings are acquired.
f [INTERNAL]: Uses the settings set on the camera.
f [SD CARD]: Uses the settings of the le inside the SD memory card inserted in the SD card slot. When this item is set to [SD CARD], insert an SD
memory card before turning on the power of the camera.
[SERVER URL]: Sets the name or address of the server to connect to. (Up to 500 characters)
[LOGIN USER]: Sets the user ID to connect to. (Up to 31 characters)
[LOGIN PASSWORD]: Sets the password to connect to. (Up to 15 characters) The set password cannot be displayed on the unit.
[SSH]: Sets when transferring les using SSH. ([ENABLE]: Uses SSH/[DISABLE]: Does not use SSH)
[SSH PORT]: Sets the port number when the SSH is used. Set to the same number as the server.
@@
NOTE
t The FTP client function does not function when [WLAN] is set in the main menu → [I/F SETUP] → [USB/LAN] → [NETWORK SEL], and [DIRECT] is
set in the main menu → [I/F SETUP] → [USB/LAN] → [WIRELESS PROPERTY] → [TYPE].
t The setting value of the SD memory card can be saved in following method.
- Select [SAVE (SD CARD)] in the main menu → [I/F SETUP] → [USB/LAN] → [FTP CLIENT SERVICE].
Saving client service settings in the SD memory card
1
Select [SAVE (SD CARD)] in the main menu → [I/F SETUP] → [USB/LAN] → [FTP CLIENT SERVICE].
The setting values of [SERVER URL], [LOGIN USER], [LOGIN PASSWORD], [SSH], and [SSH PORT] of main menu → [I/F SETUP] → [USB/LAN]
→ [FTP CLIENT SERVICE] are saved in the SD memory card.
Loading the client service settings from the SD memory card
1
Select [LOAD (SD CARD)] in the main menu → [I/F SETUP] → [USB/LAN] → [FTP CLIENT SERVICE].
The client service settings loaded from the SD memory card are reected on the settings of the camera.
Operation check tools, status indication, and initialization
You can check FTP client network connection status as follows.
r Checking connection (PING)
1
Press the <THUMBNAIL> button.
The thumbnail screen is displayed.
2
Select [PING] in the main menu → [I/F SETUP] → [USB/LAN] → [NETWORK TOOLS].
3
Press the jog dial button (or the <SET> button).
4
Perform status check of the connection with the address that has been set.
When a connection is conrmed, [PING SUCCESSFUL!] appears.
If a connection cannot be established within approximately 30 seconds, [PING FAILED!] appears. The log may indicate the cause of a failure.
r Displaying the connection log (LOG)
1
Select [LOG DISPLAY] in the main menu → [I/F SETUP] → [USB/LAN] → [NETWORK TOOLS].
2
Press the jog dial button (or the <SET> button).
The log appears.
3
After checking the log, press the <EXIT> button.
The setting menu screen returns.
@@
NOTE
t Some operations may not generate any information in the log.
t The password is indicated as [*] in the log.
r Displaying the status
1
Select [STATUS DISPLAY] in the main menu → [I/F SETUP] → [USB/LAN] → [NETWORK TOOLS].