Panasonic HL-G1 Series

To Next Page

To Previous Page

㻌

Press WKH>83@>'2:1@NH\WRPDNH

analysis mode changes. (Example:

Switching to PEAK to PEAK mode.)

3UHVVWKH>(17(5@NH\WRGHWHUPLQHWKH

mode setting.

Ramco Innovations

(

800

)

280-6933 www.panasonicsensors.com nsales

ramcoi.com

Main Page

About this Manual3
Table of Contents4
Safety Precautions6
Warning6
Caution6
Correct Handling7
Installation Environment7
Do Not Install the System in the Following7
Operating Environment7
Illuminance7
Power Supply Voltage8
Environment8
Protective Structure8
Warm-Up Time9
Countermeasures against Noise9
Power Supply10
Applicable Power Supply10
Power Supply Sequence for Sensor Head10
Instantaneous Power Failure10
Applicable Standards / Regulations11
Laser Product Handling12
Jis/Iec/Gb12
Laser Diode Sensor12
Precautions12
Warning Label13
Fda14
Export to US14
FDA Standards15
Maintenance and Inspection17
Maintenance Instructions17
Inspection17
Before Use19
System Configuration20
Accessories21
Sensor Head Accessories21
Extension Cable for Sensor Head (Optional for High-Function Type Only)22
Setting and Monitoring Software HL-G1SMI22
Type Only)22
Compact Console23
Part Names and Functions24
Installation Method25
Extension Cable25
Mounting Direction of Sensor Head26
Measurement of Transparent Objects30
O Terminal Block31
2-1 Functions and Arrangements of I/O Terminal31
Block31
I/O Circuit34
Analog Output Circuit36
Timing Chart37
Conditions When Output Data Become Unfixed39
Functions41
Classification of Functions42
Function List & Initial Values42
Operation of each Function45
3-3-1 Basic Operation45
Panel Configuration45
Basic Operation46
Screen Transition in Setting Mode49
3-3-3 Sensing Setting53
Sampling Cycle53
Shutter Time54
Light Intensity Monitor55
3-3-4 Data Processing Settings56
Average Times56
Analysis Mode57
Span59
Offset61
Zero-Set off62
3-3-5 Output Settings63
Judgment Output Selection63
Displacement Judgment65
Judgment Output off Delay67
Measurement Value Display on Panel69
3-3-6 Analog Settings70
Analog Output Selection70
Analog Scaling71
3-3-7 Alarm Settings73
Analog Output at Alarm73
Digital Output at Alarm74
Alarm Delay Times75
3-3-8 COM Settings76
Terminating Resistor Selection76
Sensor no77
Baud Rate78
Connection Mode79
Sending Delay Time80
3-3-9 System Settings81
Timing Mode81
Laser Control82
Eco Mode83
View Version84
3-3-10 Other System Settings85
Initialize85
Save86
External Input87
Timing87
Zero Set87
Reset89
Buffering Settings90
Data Buffering Operation91
Buffering Mode92
Buffering Rate93
Accumulated Amount93
Trigger Points94
Trigger Delay94
Trigger Conditions95
Buffering Operation96
Status Readout96
Last Data Point96
Binary Readout of Buffering Data97
Communications Control99
4-1 Communications Specifications100
Specifications100
Pin Arrangement100
Connecting Example with External Device101
Communications Protocol104
Communications Condition Changes104
4-2 Type and Format of Commands105
4-2-1 Commands105
Data Transmission/Reception105
4-2-2 Command Formats107
Format107
General Purpose107
Format108
Value Setting108
Format110
All Outputs Read110
Format111
Normal Read of Buffering Data111
Buffering Data111
Format112
Binary Read of Buffering Data112
Format113
Timing113
Error Response114
Bcc116
4-3 Command List117
Basic Settings117
Data Processing Settings117
Output Settings118
Analog Settings119
Alarm Settings119
System Settings120
Read Commands121
Buffering Commands121
4-4 Setting Address List123
Command Formats(MEWTOCOL)124
Error Response124
Sensing Settings125
Data Processing Settings125
Output Settings126
Analog Settings126
Alarm Settings127
System Settings127
Data Readout127
Buffering Settings128
Setting for Programmable Display129
Troubleshooting131
Corrective Actions133
Initialization136
Specifications137
Sensor Head Specifications138
Dimensions144
Sensor Head144
Characteristics149
Beam Diameter149
Mutual Interference Area151
Output Characteristics154
Revision History156

Panasonic HL-G1 Series - Page 58

Table of Contents

Related product manuals