EasyManuals Logo

Pentax K100D User Manual

Pentax K100D
95 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #42 background imageLoading...
Page #42 background image
76700 -41/94-
13-3. Writing FW
* In this step, the connection of each circuit board and the output of
a video signal are confirmed by writing FW.
* When the FW writing (for service) is done, all settings are initialized.
[Caution 1] Writing the FW is necessary whenever 0-T100
is replaced.
[Caution 2] Always use the latest version FW whenever writing the FW.
(1) Surely insert the SD card (FW for service) into the 0-T100.
(2) Connect the video cable and AC adapter to the camera.
(3) The version of CPU/DSP will be displayed on the
TV monitor
[NOTE] If you want to cancel writing firmware,
disconnect AC adapter and eject the SD card.
(4) Remove the SD card when the message as
>>> EJECT SD CARD <<< is displayed, and then
the loading of firmware will be started.
It takes approx 90 sec. until the loading is finished. (UPDATING…)
[CAUTION] Do not turn OFF the camera while loading firmware.
(5) When POWER OFF is displayed, disconnect the AC adapter
from the camera. (Leave the Video cable)
13.4 Data initialization
*If excute this initialization, all EEPROM data will be initialized (Cleared)
[Caution] When replacing 0-T100, you must excute this initialization.
In other case, s not necessary to excute Data initialization.
(1) Install SD card (For data initialization) to the camera.
(2) Connect the ACadaptor. (Initialization will be started.
It takes approx 20 sec.)
[Caution] Do not t F the power
(3) When monitor display is turn off, (“WAIT…” “COMPLETE…” )
disconnect the AC adapter.
13-5. Setting test mode
*With this setting, camera can operate even without SD card cover.
(1) Insert SD card for Test mode ON to the camera.
(2) Connect AC adaptor to the camera. (LCD will be displayed moment)
(3) Disaplay the LCD monitor then disconnect the AC adapter.
(4) Remove SD card from the camera.
(5) When connect AC adaptor again, LCD monitor will be displayed.
Also when press shutter button half way, display will be appeared on the LCD
DETECTED BOTH F/W FILE
NOW LOADING
DETECTED FIRMWARE FILE
COMPLETE LOADING
------- CPU --------
CURRENT VER.1.00.00.00
UPDATE VER.1.00.00.10
======= DSP ========
CURRENT VER.1.00.00.00
UPDATE VER.1.00.00.10
>>> EJECT SD CARD <<<
PENTAX K100D
UPDATING DSP FIRMWARE
SECTOR** >> PROGRAM
_____________
NEVER POWER OFF
PENTAX K100D
UPDATING DSP FIRMWARE
**** COMPLETE ****
VERSION 1.00.00.10
POWER OFF
WAIT
COMPLETE
VERIFY:****

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Pentax K100D and is the answer not in the manual?

Pentax K100D Specifications

General IconGeneral
Megapixel6.1 MP
Sensor typeCCD
InterfaceUSB 2.0
Color depth8 bit
Digital SLRYes
Video capabilityNo
Camera shutter speed1/4000 - 30 s
FocusTTL
Auto focusing (AF) modescentre weighted auto focus, continuous auto focus, selective auto focus
Light meteringCentre-weighted, Spot
ISO sensitivity200, 400, 800, 1600, 3200, Auto
Light exposure modesaperture priority AE, auto, shutter priority AE
Compatible memory cardssd
Display diagonal2.5 \
Display resolution (numeric)210000 pixels
Magnification0.85X x
I/O portsAV - NTSC/PAL
USB version2.0
Product colorBlack
Battery typeAA
Number of batteries supported4
Flash modesauto, Flash off, Red-eye reduction
Scene modesbeach, Candlelight, Children, Close-up (macro), Documents, Museum, Night, Night portrait, Portrait, Sunset, Landscape (scenery)
Photo effectsblack&white, Sepia
White balanceCloudy, daylight, flash, Fluorescent, manual, Shade, Tungsten
Camera shutter typeElectronic
Weight and Dimensions IconWeight and Dimensions
Depth70 mm
Width129.5 mm
Height92.5 mm
Weight570 g

Related product manuals