Pentax K100D User Manual

76700 -80/94-
(6) Turn the main switch to OFF.
(7) Insert the SD card for FW version-check [OFF] into the camera.
(8) Turn the main switch to ON while SD card cover is opened. Access lamp will blink for about 3
seconds.
(9) After the access lamp is disappeared, turn the main switch to OFF and remove the SD card
from the camera.
(10) Turn the main switch to ON while pressing MENU button. Confirm that the firmware
version is displayed on the LCD monitor as VER: x. x x If not, repeat a cancellation.
2. Updating Firmware Version (1)
[Required equipment]
Latest product Firmware for service (SD Card),
AC adaptor, fully charged battery.
[CAUTION] 1. If power is shut down during updating firmware,
electric part in the camera will be damaged.
2. When executing this updating, the camera will be
set default setting. (Menu, Custom function,
Language, Date / Time)
(1) Install the battery and connect the AC adaptor to the camera.
Then turn the main switch to OFF.
(2) Insert the SD card into the camera.
(3) The SD card cover must open until installation is completed.
(4) Turn the main switch to ON.
(5) FW version (CPU, DSP) will be appeared on the LCD monitor as shown in the figure.
If you cancel the updating, disconnect the all power at this point.
(6) Remove the SD card when the message [>>> EJECT SD CARD <<<] is appeared then starting
updating. (It takes approx 60sec for loading firmware)
[CAUTION] Do not turn OFF the camera while loading.
(7) Turn the main switch to OFF when the following message [POWER OFF] is appeared.
(Updating is completed)
(8) Insert the SD card into the camera again then
turn on the power condition with opening SD
card cover.
(9) Confirm that the latest version is displayed on
CURRENT version. (Example: VER.1.00.00.15)
(10) Remove battery and disconnect AC adapter
without removing the SD card.
(11) At the last remove the SD card.
DETECTED BOTH F/W FILE
NOW LOADING
DETECTED FIRMWARE FILE
COMPLETE LOADING
------- CPU --------
CURRENT VER.1.00.00.00
UPDATE VER.1.00.00.10
======= DSP ========
CURRENT VER.1.00.00.00
UPDATE VER.1.00.00.10
>>> EJECT SD CARD <<<
PENTAX K100D
UPDATING DSP FIRMWARE
SECTOR** >> PROGRAM
_____________
NEVER POWER OFF
PENTAX K100D
UPDATING DSP FIRMWARE
**** COMPLETE ****
VERSION 1.00.00.10
POWER OFF

Pentax K100D Specifications

General

Megapixel	6.1 MP
Sensor type	CCD
Interface	USB 2.0
Color depth	8 bit
Digital SLR	Yes
Video capability	No
Camera shutter speed	1/4000 - 30 s
Focus	TTL
Auto focusing (AF) modes	centre weighted auto focus, continuous auto focus, selective auto focus
Light metering	Centre-weighted, Spot
ISO sensitivity	200, 400, 800, 1600, 3200, Auto
Light exposure modes	aperture priority AE, auto, shutter priority AE
Compatible memory cards	sd
Display diagonal	2.5 \
Display resolution (numeric)	210000 pixels
Magnification	0.85X x
I/O ports	AV - NTSC/PAL
USB version	2.0
Product color	Black
Battery type	AA
Number of batteries supported	4
Flash modes	auto, Flash off, Red-eye reduction
Scene modes	beach, Candlelight, Children, Close-up (macro), Documents, Museum, Night, Night portrait, Portrait, Sunset, Landscape (scenery)
Photo effects	black&white, Sepia
White balance	Cloudy, daylight, flash, Fluorescent, manual, Shade, Tungsten
Camera shutter type	Electronic

Weight and Dimensions

Depth	70 mm
Width	129.5 mm
Height	92.5 mm
Weight	570 g