peplink Balance 30 User Manual

Name: peplink Balance 30
Brand: peplink
Rating: 4 (1 reviews)

111 pages

To Next Page

Reserved. PePLink and the PePLink logo are trademarks of PePLink Ltd. Other brands or products

mentioned may be trademarks or registered trademarks of their respective owners.

PePLink Balance Series v4.0

PePLink Balance 30/200/300/380/700

User Manual

Rev. 2.0

June 07

Default Chapter1
- User Manual1
- Table of Contents2
1 Introduction and Scope4
2 Glossary4
3 Product Features5
- Supported Network Features5
- Other Supported Features5
4 Package Contents6
- P Epl Ink Balance 30 / 200 / 3006
- P Epl Ink Balance 380 / 7006
5 Peplink Balance Overview7
- P Epl Ink Balance 2007
- P Epl Ink Balance 30 / 3009
- P Epl Ink Balance 38011
- P Epl Ink Balance 70014
6 Installation17
- Connecting the Network with Peplink Balance17
- Configuring Computers on the Lan18
7 Basic Configuration21
- Connecting to Web Administration Interface21
- Configuration with Setup Wizard22
- Onfiguration with Etup Izard22
- Advanced Setup23
8 Configuration of Lan Interface(S)24
9 Drop-In Mode27
10 Configuration of Wan Interface(S)30
- Dhcp Connection30
- Static Ip Connection33
- Pppoe Connection36
- Gre Connection38
- Smtp Forwarding43
- Dynamic Dns Settings43
- Wan Health Check44
11 Firewall Configuration47
12 Management of Outbound Traffic to Wan51
- Outbound Traffic Policy51
- Fine Tuning Load Distribution for Individual Services52
13 Management of Inbound Access from Wan57
- Definition of Servers on Lan57
- Definition of Services58
- Definition of Porting Forwarding62
- Definition of Dns Records64
14 Configuration of Nat Mappings75
15 Miscellaneous Settings77
- High Availability77
- Traffic Prioritization79
16 System Settings79
- Admin Security79
- Firmware Upgrade82
- Time83
- Email Notification84
- Remote Syslog85
- Snmp85
- Reporting Server87
- Saving and Loading Configurations89
- Flash Management90
- Reboot91
- Ping Test91
- Traceroute Test92
17 Status93
- Device93
- Link Usage Status94
- Active Sessions95
- Dhcp Clients96
- Log96
Appendix A. Restoration of Factory Defaults97
- N Etwork a Ddress T Ranslation (Nat)98
Appendix B. Routing under Dhcp, Static Ip, and Pppoe98
- Routing Via Network Address Translation (Nat)98
- Routing Via Ip Forwarding98
Appendix C. Case Studies99
- Performance Optimization99
- Aintaining the same Ip Address Throughout Aession100
- Bypassing the Firewall to Access Hosts on Lan102
- Firewall to Acces Host on LAN102
- Inbound Access Restriction103
- Outbound Access Restriction104
Appendix D. Troubleshooting105
Appendix E. Product Specifications107
- P Epl Ink Balance 200107
- P Epl Ink Balance and P Epl Ink Balance108
- Peplink Balance109
- P Epl Ink Balance 700110

Questions and Answers:

S
Sarah JonesJul 26, 2025
How to fix Peplink Network Router FTP upload stalls?
- E
  Evan TaylorJul 26, 2025
  If file transfers via FTP stall after a few kilobytes, the Maximum Transmission Unit (MTU) or MSS setting may need adjustment. The default MTU is 1500. For most DSL users, it's recommended to use MTU 1492. If the problem persists, try smaller values (e.g., 1462, 1420, 1400) until the issue is resolved.