PDP-5000EX
146
1234
1234
C
D
F
A
B
E
Command
Division
Function
command
Reception Point
Last
Memory
Only
FAY is
Effective
Remarks
F
FAJ SGL Determining the flag of the unit adjustment in "adjustment is completed"
¶¶
FAN SGL Factory mode off
¶¶ ¶
FAY SGL Factory mode on
¶¶
FST
S01 FNC Set each memory setting of MTB side to the shipment state of Japan.
¶¶
S02 FNC
Set each memory setting of MTB side to the shipment state of North America.
¶¶
S03 FNC Set each memory setting of MTB side to the shipment state of Europe.
¶¶
G
GHI ∗∗∗ ADJ User white balance : GREEN highlight
¶¶
Main
GLW ∗∗∗ ADJ User white balance : GREEN lowlight
¶¶
Main
I
INP
S01 FNC Input switch: INPUT 1
¶
Main
S02 FNC Input switch: INPUT 2
¶
Main
S03 FNC Input switch: INPUT 3
¶
Main
S04 FNC Input switch: INPUT 4
¶
Main
S05 FNC Input switch: INPUT 5
¶
Main
S06 FNC Input switch: INPUT 6
¶
Main
M
MKC
S00 FNC MASK off
¶
Mod
¶
S01 FNC H ramp (slant 1) M
¶
Mod
¶
S02 FNC H ramp (slant 4) M
¶
Mod
¶
S03 FNC Slanting ramp M
¶
Mod
¶
S04 FNC 30 for aging
¶
Mod
¶
S05 FNC 05 for aging
¶
Mod
¶
S06 FNC Erasing afterimage 1
¶
Mod
¶
S07 FNC Erasing afterimage 2 (RGB: zigzag, V: reverse)
¶
Mod
¶
S08 FNC White (change in luminance level)
¶
Mod
¶
S09 FNC PEAK SEEK RASTER
¶
Mod
¶
S10 FNC For technique evaluation 1
¶
Mod
¶
MKS
S00 FNC MASK off
¶
Mod
S01 FNC H ramp (slant 1)
¶
Mod
¶
S02 FNC H ramp (slant 4)
¶
Mod
¶
S03 FNC V ramp (slant 1)
¶
Mod
¶
S04 FNC Slanting ramp
¶
Mod
¶
S05 FNC Window (Hi= 870, Lo= 102)
¶
Mod
¶
S06 FNC Window (Hi= 1023, Lo= 102)
¶
Mod
¶
S07 FNC Window (Hi= 1023)
¶
Mod
¶
S08 FNC Window (Hi= 1023) 4 %
¶
Mod
¶
S09 FNC Window (Hi= 1023) 1.25 %
¶
Mod
¶
S10 FNC Window (1/7 LINE)
¶
Mod
¶
S11 FNC STRIPE (MGT/GRN)
¶
Mod
¶
S12 FNC STRIPE (GRN/MGT)
¶
Mod
¶
S13 FNC B & W, checker (1 line)
¶
Mod
¶
S14 FNC B & W, checker (2 lines)
¶
Mod
¶
S15 FNC B & W, checker (4 lines)
¶
Mod
¶
S16 FNC B & W, checker (8 lines)
¶
Mod
¶
S17 FNC COLOR BAR
¶
Mod
¶
Mod Main
To Next Page
Loading...
Need help?
General
