Shifting to NEUTRAL from any gear will maintain the
selected view (Zoom or Standard) as long as the vehicle
is below 8 mph (13 km/h).
If the vehicle is in PARK, Zoom View is available until
the gear selector is placed in DRIVE or REVERSE and
speeds are at or above 8 mph (13 km/h).
NOTE:
•
If the vehicle is in DRIVE, NEUTRAL, or REVERSE,
and speed is greater than or equal to 8 mph
(13 km/h), Zoom View is unavailable and the icon
will appear gray.
•
While in Zoom View, the guidelines will not be
visible.
Deactivation
The system is deactivated in the following conditions if
it was activated automatically:
•
When the vehicle is shifted out of REVERSE with
camera delay turned on, the camera image will con-
tinue to be displayed for up to 10 seconds, unless
the vehicle speed exceeds 8 mph (13 km/h), the
vehicle is shifted into PARK or the ignition is placed
in the OFF position. There is a touchscreen X button
to disable the display of the camera image.
•
When the vehicle is shifted out of REVERSE with
camera delay turned off, the Surround View Camera
mode is exited and the last known screen appears
again.
The system is deactivated in the following conditions if
it was activated manually from the Uconnect controls
menu via the Surround View button, Back Up Camera
button, Cargo Camera button or Forward Facing Cam-
era button:
•
The touchscreen X button on the display is pressed
•
Vehicle is shifted into PARK
•
Ignition is placed in the OFF position
•
Vehicle speed is over 8 mph (13 km/h) for
10 seconds
NOTE:
If the Surround View Camera, Cargo Camera, Back Up
Camera, or Forward Facing Camera is activated manu-
ally, and the vehicle is shifted into REVERSE, deactiva-
tion methods for automatic activation are assumed.
The camera delay system is turned off manually
through the Uconnect Settings menu
page 174.
NOTE:
•
If snow, ice, mud, or any foreign substance builds up
on the camera lenses, clean the lenses, rinse with
water, and dry with a soft cloth. Do not cover the
lenses.
•
If a malfunction with the system has occurred, see
an authorized dealer.
Cargo Camera With Dynamic Centerline — If Equipped
The Dynamic Centerline feature provides an overlay on
the Cargo Camera display screen that aligns to the cen-
ter of the pickup box to aid in hooking up a fifth-wheel
camper or gooseneck trailer. The centerline auto aligns
to the center of the pickup box, and can also be manu-
ally adjusted. The centerline will adjust in response to
steering angle inputs, and will not obstruct the goose-
neck receiver or an approaching trailer gooseneck in
the camera feed.
Activation
The Dynamic Centerline feature can be activated
through the Uconnect settings by pressing the Cargo
Camera button, followed by the Dynamic Centerline
button on the touchscreen.
If the Dynamic Centerline feature is turned on, the
overlay will display any time the Cargo Camera image is
displayed.
Adjusting Centerline
To manually adjust the centerline, proceed as follows:
1. Press the Adjust Centerline button located in the
bottom right corner of the Cargo Camera display.
2. Use the arrows on the bottom left corner of the
Cargo Camera display to adjust the centerline hori-
zontally or vertically.
3. Once the desired position is achieved, press the
Accept button to set the centerline to the newly
specified position.
Deactivation
The Dynamic Centerline feature will automatically be
deactivated whenever the Cargo Camera display is
deactivated. It can also be manually deactivated
through the Uconnect Settings.
Cargo Camera Zoom View
When the Cargo Camera image is being dis-
played, and the vehicle speed is below
8 mph (13 km/h) while in any gear selector
position, Zoom View is available. By pressing
the “magnifying glass” icon in the upper left of the dis-
play screen, the image will zoom in to four times the
standard view. Pressing the icon a second time will
return the view to the standard Cargo Camera display.
STARTING AND OPERATING 149
4
To Next Page
Loading...
