Rohde & Schwarz R&S ZNB - System:communicate:rdevice

Command Reference
R&S
®
ZNB/ZNBT
1091User Manual 1173.9163.02 ─ 53
[SENSe<Ch>:]CORRection:EDELay<PhyPt>:ELENgth.................................................... 1128
[SENSe<Ch>:]CORRection:EDELay<PhyPt>[:TIME]....................................................... 1129
[SENSe:]CORRection:EDELay:VNETwork...................................................................... 1129
[SENSe<Ch>:]CORRection:EWAVe[:STATe]................................................................... 1130
[SENSe<Ch>:]CORRection:LOSS<PhyPt>..................................................................... 1130
[SENSe<Ch>:]CORRection:LOSS<PhyPt>:AUTO........................................................... 1130
[SENSe<Ch>:]CORRection:LOSS<PhyPt>:FREQuency...................................................1131
[SENSe<Ch>:]CORRection:LOSS<PhyPt>:OFFSet.........................................................1131
[SENSe<Ch>:]CORRection:OFFSet<PhyPt>[:STATe]...................................................... 1131
[SENSe<Ch>:]CORRection:OFFSet<PhyPt>:COMPensation[:STATe]................................1132
[SENSe<Ch>:]CORRection:OFFSet<PhyPt>:DFComp[:STATe]?.......................................1132
[SENSe<Ch>:]CORRection:PCAL..................................................................................1133
[SENSe<Ch>:]CORRection:POWer:DATA.......................................................................1133
[SENSe<Ch>:]CORRection:POWer:DATA:PORT<PhyPt>................................................ 1133
[SENSe<Ch>:]CORRection:POWer<PhyPt>[:STATe]....................................................... 1134
[SENSe<Ch>:]CORRection:POWer<PhyPt>:ACQuire......................................................1135
[SENSe<Ch>:]CORRection:POWer<PhyPt>:AWAVe[:STATe]............................................1136
[SENSe<Ch>:]CORRection:POWer<PhyPt>:IMODulation:ACQuire...................................1136
[SENSe<Ch>:]CORRection:STIMulus?...........................................................................1137
[SENSe<Ch>:]CORRection:STIMulus:PORT<PhyPt>?.................................................... 1137
[SENSe<Ch>:]CORRection:COLLect:AUTO:ASSignment:ALL:COUNt?.............................1137
[SENSe<Ch>:]CORRection:COLLect:AUTO:ASSignment:COUNt?....................................1138
[SENSe<Ch>:]CORRection:COLLect:AUTO:ASSignment:DEFine:DEFault........................ 1138
[SENSe<Ch>:]CORRection:COLLect:AUTO:ASSignment:DEFine:TPORt:DEFault..............1139
[SENSe<Ch>:]CORRection:COLLect:AUTO:ASSignment:DELete:ALL.............................. 1140
[SENSe<Ch>:]CORRection:COLLect:AUTO:ASSignment<Asg>:ACQuire..........................1140
[SENSe<Ch>:]CORRection:COLLect:AUTO:ASSignment<Asg>:DEFine............................1140
[SENSe<Ch>:]CORRection:COLLect:AUTO:ASSignment<Asg>:DEFine:TPORt.................1142
[SENSe<Ch>:]CORRection:COLLect:AUTO:SAVE.......................................................... 1142
[SENSe<Chn>:]CORRection:PSTate?............................................................................ 1142
[SENSe<Chn>:]CORRection:SSTate?............................................................................ 1143
[SENSe:]CORRection:COLLect:AUTO:CKIT <Characterization>
Generates a characterization (cal kit file) with the specified name containing the cal kit
data of the active calibration unit (selected via SYSTem:COMMunicate:RDEVice:
AKAL:ADDRess). The cal kit file can be saved to a directory on the analyzer, to the
calibration unit's internal (flash) memory or to an SD card inserted at the calibration unit
(if available).
Note that this command can only be executed if the number of cal unit ports is less or
equal to the number of test ports. Furthermore the command assumes the "canonical"
assignment of cal unit ports to test ports: cal unit port 1 assigned to test port 1, cal unit
port 2 assigned to test port 2 etc. The new command [SENSe:]CORRection:
COLLect:AUTO:CKIT:PORTs allows for flexible assignments.
Setting parameters:
<Characterization> Location of the created characterization / cal kit file (string
parameter, extension *.calkit):
If a path is specified, the file is saved to the analyzer's hard disk.
The default directory (MMEMory:CDIRectory) is not used.
SCPI Command Reference