Command Reference
R&S
®
ZNB/ZNBT
875User Manual 1173.9163.02 ─ 53
Example:
*RST; :CALC:SMO ON
Activate smoothing for the default trace.
CALC:SMO:APER 0.5
Reduce the smoothing aperture to 0.5 %.
Manual operation: See "Aperture" on page 334
8.3.1.18 CALCulate:STATistics...
The CALCulate:STATistics... commands evaluate and display statistical and
phase information of the trace.
CALCulate<Chn>:STATistics[:STATe]............................................................................... 875
CALCulate<Chn>:STATistics[:STATe]:AREA..................................................................... 876
CALCulate<Chn>:STATistics:DOMain:USER.................................................................... 876
CALCulate<Chn>:STATistics:DOMain:USER:SHOW......................................................... 877
CALCulate<Chn>:STATistics:DOMain:USER:STARt.......................................................... 877
CALCulate<Chn>:STATistics:DOMain:USER:STOP...........................................................877
CALCulate<Chn>:STATistics:EPDelay[:STATe]..................................................................878
CALCulate<Chn>:STATistics:MMPTpeak[:STATe]..............................................................878
CALCulate<Chn>:STATistics:MSTDdev[:STATe]................................................................878
CALCulate<Chn>:STATistics:FORMat..............................................................................878
CALCulate<Chn>:STATistics:NLINear:COMP:LEVel.......................................................... 878
CALCulate<Chn>:STATistics:NLINear:COMP:PHASe........................................................879
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER.......................................... 879
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:SHOW................................879
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:STARt................................ 880
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:STOP.................................880
CALCulate<Chn>:STATistics:NLINear:COMP:REFerence.................................................. 880
CALCulate<Chn>:STATistics:NLINear:COMP:RESult?.......................................................881
CALCulate<Chn>:STATistics:NLINear:COMP:RLEVel........................................................881
CALCulate<Chn>:STATistics:NLINear:COMP:RMARker.....................................................882
CALCulate<Chn>:STATistics:NLINear:COMP:RPHase.......................................................882
CALCulate<Chn>:STATistics:NLINear:COMP:RPHase.......................................................882
CALCulate<Chn>:STATistics:NLINear:COMP[:STATe]........................................................883
CALCulate<Chn>:STATistics:RESult?.............................................................................. 883
CALCulate<Chn>:STATistics:RMS[:STATe]....................................................................... 884
CALCulate<Chn>:STATistics:SFLatness[:STATe]...............................................................884
CALCulate<Chn>:STATistics[:STATe] <Boolean>
Displays or hides all statistical results in the diagram area of trace no. <Chn> except
the compression point results.
Tip: You can display or hide the "Min/Max/Peak-Peak", "Mean/Std Dev/RMS",
"Phase/El Length" and "Flatness/Gain/Slope" results separately; see example below.
Suffix:
<Chn>
.
Channel number used to identify the active trace
SCPI Command Reference
To Next Page
Loading...
