Rohde & Schwarz R&S ZNB - Page 1175

Command Reference
R&S
®
ZNB/ZNBT
1175User Manual 1173.9163.02 ─ 53
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution].......................................................1177
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:CONTrol......................................... 1177
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:SELect........................................... 1178
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:SELect:CONTrol..............................1178
[SENSe<Ch>:]SEGMent<Seg>:DEFine..........................................................................1179
[SENSe<Ch>:]SEGMent<Seg>:DEFine:SELect...............................................................1181
[SENSe<Ch>:]SEGMent<Seg>:DELete:ALL................................................................... 1181
[SENSe<Ch>:]SEGMent<Seg>:DELete[:DUMMy]............................................................1182
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:CENTer?..................................................... 1182
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:SPAN?........................................................1182
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:STARt.........................................................1183
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:STOP......................................................... 1183
[SENSe<Ch>:]SEGMent<Seg>:INSert............................................................................1183
[SENSe<Ch>:]SEGMent<Seg>:INSert:SELect................................................................ 1185
[SENSe<Ch>:]SEGMent<Seg>:POWer[:LEVel]............................................................... 1186
[SENSe<Ch>:]SEGMent<Seg>:PORT<PortId>:POWer[:LEVel].........................................1186
[SENSe<Ch>:]SEGMent<Seg>:PORT<PortId>[:STATe]................................................... 1187
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol........................................................1187
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol:ALL.................................................1188
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol:CONTrol.......................................... 1189
[SENSe<Ch>:]SEGMent<Seg>:POWer[:LEVel]:CONTrol................................................. 1190
[SENSe<Ch>:]SEGMent<Seg>:SWEep:DWELl...............................................................1191
[SENSe<Ch>:]SEGMent<Seg>:SWEep:DWELl:CONTrol................................................. 1191
[SENSe<Ch>:]SEGMent<Seg>:SWEep:GENeration........................................................1192
[SENSe<Ch>:]SEGMent<Seg>:SWEep:POINts.............................................................. 1193
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME................................................................. 1193
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME:CONTrol....................................................1194
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME:SUM?....................................................... 1194
[SENSe<Ch>:]SEGMent:COUNt?
Returns the number of sweep segments in the channel including all segments that are
switched off ([SENSe<Ch>:]SEGMent<Seg>[:STATe] OFF).
Suffix:
<Ch>
.
Channel number
Example:
SEGM:ADD
Create a new sweep segment no. 1 in channel no. 1 using
default settings.
SEGM OFF
Disable the measurement in the created sweep segment.
SEGM:COUN?
Query the number of segments.
Usage: Query only
Manual operation: See "Table Columns" on page 403
SCPI Command Reference