MX-M700N SIMULATION 7 – 35
44-14
Purpose
Adjustment/Setup/Operation data output/
Check (Display)
Function (Purpose)
Used to check the output level of the tem-
perature sensor and the humidity sensor.
Section
Image process
(Photoconductor/Developing)
Operation/Procedure
The output levels of the temperature sensor and the humidity sen-
sor in the developing unit are displayed.
44-16
Purpose
Adjustment/Setup/Operation data output/
Check (Display)
Function (Purpose)
Used to check the toner concentration con-
trol data.
Section
Process (Developing)
Operation/Procedure
46
46-2
Purpose
Adjustment
Function (Purpose)
Used to adjust the copy density in all the
copy modes (Auto, Text, Text/Photo, and
Photo mode).
Section
—
Operation/Procedure
1) Select the number corresponding to the copy mode to be
adjusted with 10-key. (Select one of 3 - 6.)
2) Press the [START] key.
3) Enter the copy density level with 10-key.
4) Press the [P] or [START] key.
The adjustment value is set.
When [START] key is pressed, copy is performed and the
adjustment value is set simultaneously.
Check the density of the printed copy image.
NOTE: When the copy image density is adjusted with this simula-
tion, the copy image densities of all the copy modes are
changed to the copy image density level set with this simu-
lation. That is, the copy image density of each copy mode
set with SIM 46-9, 10, 11 is changed to the copy image
density level adjusted with this simulation.
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
TH-DV (Not used) Developing section temperature
sensor
0 - 255
TH-RA (Not used) Room temperature sensor 0 - 255
TH-CL Process section temperature
sensor
0 - 255
TH-EX Paper discharging section
temperature sensor
0 - 255
HUS-DV Developing section humidity
sensor
0 - 255
HUS-TC (Not used) Process section humidity sensor 0 - 255
HUMIDITY
AREA
Humidity area
INT HUMIDITY
AREA
Humidity area when setting the toner concentration
control level (SIM 25-2)
TARGET LEVEL Current toner concentration control level
DEV REF Toner concentration when setting the toner
concentration control level (SIM 25-2)
HUMIDITY
(TARGET)
Toner concentration correction value for humidity
A Toner concentration correction value for change in
developing bias voltage
B Toner concentration value for developer life
SIMULATION 44-12
DM DATA, PATCH/BASE DATA DISPLAY.
DMLED: 000 PC LED: 000 END DV_BS: 000
PT1/BS1 PT2/BS2 PT3/BS3
ID(1): 000/000 000/000 000/000
ID(2): 000/000 000/000 000/000
ID(3): 000/000 000/000 000/000
ID(4): 000/000 000/000 000/000
ID(5): 000/000 000/000 000/000
ID(6): 000/000 000/000 000/000
ID(7): 000/000 000/000 000/000
ID(8): 000/000 000/000 000/000
SIMULATION 44-14
SENSOR DATA DISPLAY MONITOR.
TH-DV: 255
TH-RA: 255
TH-CL: 255
TH-EX: 255
HUS-DV: 255
HUS-TC: 255
Item
Setting
range
Default
0 TRAY SELECT Paper feed tray
selection
1 COPY START Copy START
(Default)
2 EXP LEVEL Exposure level
selection
3 AE 3.0 AE mode 0 - 99 50
4 CH 3.0 Text mode 3.0
5 MIX 3.0 Text/Photo mode
3.0
6 PHOTO 3.0 Photo mode 3.0
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual paper feed
6 LCC Side LCC
SIMULATION 44-16
TONER CONTROL STANDARD LEVEL DISPLAY.
HUMIDITY AREA: 7
INT HUMIDITY AREA: 7
TARGET LEVEL = DEV REF + HUM(TARGET)+A+B
114 = 114 + 0( 0)+0 + 0
To Next Page
Loading...
