MX-M700N SIMULATION 7 – 8
4. Details of simulation
1
1-1
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the scan-
ner (read) unit and its control circuit.
Section
Optical (Image scanning)
Operation/Procedure
1) Select the operation mode with 10-key.
2) Press [START] key.
The scanner performs scanning at the speed corresponding to
the operation mode.
1-2
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of sensor and
detector in the scanning (read) section and
the related circuit.
Section
Optical (Image scanning)
Operation/Procedure
The sensor and detector operation conditions are displayed.
The active sensors and detectors are highlighted.
• The scanner (read) unit is in the home position.: "MHPS" section
is highlighted.
• The scanner (read) unit is not in the home position.: "MHPS" is
normally displayed.
2
2-1
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the auto-
matic document feeder unit and the control
circuit.
Section
DSPF
Operation/Procedure
1) Select the operation mode with 10-key.
2) Press [START] key.
The SPF repeat paper feed, transport, and paper exit at the speed
corresponding to the operation mode.
The operation can be stopped with the [SYSTEM SETTINGS] key.
2-2
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the sen-
sors and detectors in the automatic docu-
ment feeder unit and the related circuits.
Section
DSPF
Operation/Procedure
The sensor and detector operation conditions are displayed.
The active sensors and detectors are highlighted.
2-3
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the loads
in the automatic document feeder unit and
the control circuits.
Section
DSPF
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press the [START] key.
The load selected in procedure 1 is operated.
The operation can be stopped with the [SYSTEM SETTINGS]
key.
1 HIGH SPEED High speed (220mm/s)
2 LOW SPEED Low speed (110mm/s)
MHPS Optical system home position
SIMULATION 1-1
SCANNER CHECK. SELECT 1-2, AND PRESS START.
1. HIGH SPEED
2. LOW SPEED
1
SIMULATION 1-2
SCANNER SENSOR CHECK..
MHPS
1 HIGH SPEED (220mm/sec) High speed
2 LOW SPEED (110mm/sec) Low speed
3 TOP SPEED (360mm/sec) Top speed
SSET SPF sensor
SOCD Open/close sensor
SCOV Paper feed cover sensor
SPED2 Document set sensor (Lower)
SPED1 Document set sensor (Upper)
SPPD1 Document transport sensor 1
SPPD2 Document transport sensor 2
SPPD3 Document transport sensor 3
SPPD4 Document transport sensor 4
SPOD Document exit sensor
SWDn Document width sensor (n → 1 (inside) to 6 (outside))
SPLSn Document length sensor (n → 1 (inside) to 2 (outside))
CISSET CIS installation detection
STSET Stamp unit installation sensor
STUD Tray upper limit sensor
STLD Tray lower limit sensor
SWD_LEN SPF guide plate position (unit: 0.1mm)
SWD_AD SPF document width detection volume output AD
value
SIMULATION 2-1
SPF AGING TEST. SELECT 1-3, AND PRESS START.
1. HIGH SPEED
2. LOW SPEED
3. TOP SPEED
2㩷
SIMULATION 2-2
SPF SENSOR CHECK.
SSET SOCD SCOV SPED2
SPED1 SPPD1 SPPD2 SPPD3
SPPD4 SPOD SWD6 SWD5
SWD4 SWD3 SWD2 SWD1
SPLS2 SPLS1 CISSET STSET
STUD STLD
SWD_LEN: 2100 SWD_AD: 600
To Next Page
Loading...
