Sharp MX-M700N - [12] OTHERS; System Settings Overview; Counter Specifications

MX-M700N OTHERS 12 – 1
MX-M700N
5GTXKEG/CPWCN

[12] OTHERS
1. System settings
A. Count specification
(1) Paper exit system counter
Large size: A3, 11 x 17. (Greater size than paper length 384mm)
* ( ): Count-up number when setting to the large size single count up.
(2) Document, finishing, paper feed system counter
Counter Count-up timing
Count-up number
Clear
Single-side copy Duplex copy
Paper feed tray -
Main unit paper exit
Paper feed tray -
ADU
ADU -
Paper feed tray
Small size Large size Small size Large size Small size Large size
Total counter (Note) When transfer is
completed
1 2 (1) 1 2 (1) 1 2 (1) -
Maintenance counter When transfer is
completed
1 2 (1) 1 2 (1) 1 2 (1) Sim24-4
Developer counter When transfer is
completed
1 2 (1) 1 2 (1) 1 2 (1) Sim24-5
All valid paper counter (Note) When paper exit 1 2 (1) - - 2 4 (2) -
Copy counter (Copy valid paper) When paper exit 1 2 (1) - - 2 4 (2) Sim24-6
FAX counter When paper exit 1 2 (1) - - 2 4 (2) Sim24-10
Print counter When paper exit 1 2 (1) - - 2 4 (2) Sim24-9
Internet FAX counter When paper exit 1 2 (1) - - 2 4 (2) Sim24-15
Document filing counter When paper exit 1 2 (1) - - 2 4 (2) Sim24-15
Right side paper exit counter When center paper exit 1 2 (1) - - 2 4 (2) -
Other counter (Self print, etc.) When paper exit 1 2 (1) - - 2 4 (2) Sim24-9
Counter Mode Count event Count-up condition Clear
SPF counter All modes SPF paper feed number Count is made when starting SPF paper pick. Sim24-3
Finish stamp counter FAX send Internet
FAX send
Finish stamp use
number
Count is made when stamp is ON. Sim24-3
Staple counter All modes
(Including inserter
stand alone
process)
Staple number Count is made when bundle exit process is completed.
Double count is made when stapling two positions.
In the inserter stand alone mode, count is made when
process is completed.
Sim24-3
Punch counter All modes
(Including inserter
stand alone
process)
Punch number Count is made when bundle exit process is completed.
1 count regardless of the kind of the punch unit (2-hole,
3-hole, etc.)
In the inserter stand alone mode, count is made when
process is completed.
Sim24-3
Saddle staple counter All modes
(Including inserter
stand alone
process)
Saddle staple number Count is made when bundle exit process is completed.
Only one count is added.
In the inserter stand alone mode, count is made when
process is completed.
Sim24-3
Scan total counter All modes Scan number Count is made when scan is completed. Sim24-3
ADU counter All modes ADU paper feed number Count is made when paper feed from the ADU section
is started.
Sim24-2
Inserter counter All modes
(Including inserter
offline process)
Inserter tray paper feed
number
Count is made when paper feed from the inserter tray is
started.
In the inserter stand alone mode, count is made when
process is completed.
Sim24-3
Paper feed
counter
Manual paper feed
tray
All modes Tray paper feed number Count is made when paper feed from each tray is
started.
Sim24-2
Paper feed tray 1 Sim24-2
Paper feed tray 2 Sim24-2
Paper feed tray 3 Sim24-2
Paper feed tray 4 Sim24-2
LCC Sim24-2