MF2
Resolution
Offset
Temp XXX °C
Reset
Set
Set
3.4
3.5
3.6
Enter Value 0100 µm
4)
Enter Value ± 000000 mm
Plausib(ility)
Set
3.7
off 200 ms normal
4
5
Act.State
Function
Distance
UpperLimit
LowerLimit
Service
Laser
Level
UpperTemp
LowerTemp
Plausib(ility)
Ready
Bus Status
Enter Value ± 003000 mm
Enter Value ± 002990 mm
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
3.4.1
3.4.2
3.4.3
3.4.3.1
3.4.3.2
3.4.4.1
3.4.4.2
3.4.4.3
3.4.4.4
3.4.4.5
3.4.4.6
3.4.4.7
3.4.4
on off
on off
on off Enter Value ± 70 °C
on off
on off
Enter Value ± 00 °C
active 0 active 1
Distance Service MonitorSpeed
3)
on off
on off
Set
no yes
Set
Set
Set
Set
Limit
Sign
Set
Set
3.4.5.1
3.4.5.2
Speed
3.4.5
Enter Value 0,1...9,9 m/s
± – +
Code
XXX.XXX m
Ver. X.X
Serial
2)
Baudrate
Data
MF1
Enter value 000
3.1
3.1
3.1
Set
Esc
Esc
Set
Set
Set
Set
Set
2
1
3.2
3.3
3.2.1
3.2.2
3.3
3.3
115,2 kBd 38,4 kBd 19,2 kBd 9,6 kBd 4,8 kBd
7, e, 1 8, e, 1 8, n, 1
siehe nächste Seite/see next page
Act.State
Function
Distance
UpperLimit
LowerLimit
Service
Laser
Level
UpperTemp
LowerTemp
Plausib(ility)
Ready
Bus Status
Enter Value ± 002000 mm
Enter Value ± 001990 mm
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
3.3.1
3.3.2
3.3.3
3.3.3.1
3.3.3.2
Limit
Sign
SetSet
Set
3.3.5.1
3.3.5.2
3.3.4.1
3.3.4.2
3.3.4.3
3.3.4.4
3.3.4.5
3.3.4.6
3.3.4.7
3.3.4
on off
on off
on off Enter Value ± 70 °C
on off
on off
Enter Value ± 00 °C
active 0 active 1
Speed
3.3.5
_
Distance
_
Service
_
SleepMode
_
Preset
_
Speed
_
Monitor
3)
Enter Value ± 000000 mm
on off
on off
SSI
1)
Profibus
1)
RS 422
1)
3.1
DeviceNet
1)
3.1
Hiperface
1)
Enter Value 0,0 m/s
Parameter
3
Esc
3.4
Esc
3.4
Esc
3.4
Esc
3.4
Esc
3.4
Esc
3.5
Esc
3.5
Esc
3.5
Esc
3.5
Esc
3.5
Esc
4
Esc
4
Esc
4
± – +
Hinweis Parameteränderungen, die mit bestätigt werden, sind sofort aktiv und nichtflüchtig gespeichert.
Hierbei muss der Reflektor im Sichtfeld des Sensors sein. Während der Änderung darf keine
Buskommunikation aktiv sein.
Note Parameter changes that are acknowledged with are immediately effective and permanentely stored.
During parameter changes and while saving the reflector must be in sight of the sensor.
No bus communication is allowed during parameter changes.
To Next Page
Loading...
