Siemens SIMOCODE pro V MR

Table of contents
SIMOCODE pro
6 System Manual, 05/2019, A5E40507475002A/RS-AD/004
13 Commissioning, service, troubleshooting.............................................................................................. 255
13.1 General information about commissioning and service ....................................................... 255
13.2 Commissioning..................................................................................................................... 257
13.2.1 Commissioning with PROFIBUS .......................................................................................... 257
13.2.1.1 PROFIBUS commissioning steps ........................................................................................ 257
13.2.1.2 Setting the PROFIBUS DP address..................................................................................... 258
13.2.1.3 Diagnostics via LED display on the basic unit and on the operator panel (PROFIBUS) ..... 259
13.2.1.4 Diagnostics via LED display on the modules DM-F Local or DM-F PROFIsafe .................. 259
13.2.2 Commissioning with PROFINET .......................................................................................... 260
13.2.2.1 PROFINET commissioning steps ........................................................................................ 260
13.2.2.2 Setting IP parameters and PROFINET device name .......................................................... 261
13.2.2.3 Setting the time manually after switch-on or recovery of the supply voltage ....................... 263
13.2.2.4 Diagnostics via LED display on the basic unit and on the operator panel (PROFINET) ..... 264
13.2.3 Commissioning with Modbus ............................................................................................... 265
13.2.3.1 Commissioning with Modbus RTU ....................................................................................... 265
13.2.4 Commissioning with EtherNet/IP ......................................................................................... 270
13.2.4.1 EtherNet/IP commissioning steps ........................................................................................ 270
13.2.4.2 Setting IP parameters and EIP device name ....................................................................... 271
13.2.4.3 Set the time manually after switch-on or recovery of the supply voltage ............................. 273
13.2.4.4 Diagnostics via LED display on the basic unit and on the operator panel with
EtherNet/IP ........................................................................................................................... 274
13.3 Service ................................................................................................................................. 275
13.3.1 Preventive maintenance ...................................................................................................... 275
13.3.2 Backing up and saving parameters...................................................................................... 277
13.3.3 Replacing SIMOCODE pro components ............................................................................. 279
13.3.4 Exchanging a 3UF52 operator panel for a 3UF720 operator panel .....................................
283
13.
3.5 Restoring factory settings .................................................................................................... 285
13.3.6 Firmware update of device components .............................................................................. 286
13.3.7 Support Request .................................................................................................................. 287
13.4 Troubleshooting ................................................................................................................... 288
13.4.1 Error buffer ........................................................................................................................... 288
13.4.2 Event memory ...................................................................................................................... 290
13.4.3 Alarms, faults, and system events - error handling .............................................................. 291
14 Safety and commissioning information for Ex areas ............................................................................. 303
14.1 Motor protection functions (overload protection, thermistor protection) .............................. 303
14.1.1 Module integration ............................................................................................................... 303
14.1.2 Information and standards ................................................................................................... 304
14.1.3 Installation and commissioning – motor protection functions (overload protection,
thermistor protection) ........................................................................................................... 305
14.1.3.1 Operating Instructions .......................................................................................................... 305
14.1.3.2 Setting the rated motor current ............................................................................................ 305
14.1.3.3 SIMOCODE pro with thermistor input .................................................................................. 307
14.1.3.4 Sensor circuit wiring ............................................................................................................. 308
14.1.3.5 Short-circuit protection for type of coordination 2 according to IEC 60947-4-1 ................... 309
14.1.3.6 Cable protection ................................................................................................................... 309
14.1.3.7 Test ...................................................................................................................................... 309
14.1.3.8 Further safety guidelines ...................................................................................................... 311
14.1.3.9 Ambient conditions ............................................................................................................... 311
14.1.3.10 Safety values ........................................................................................................................ 312