Siemens SINAMICS Series User Manual

Table of contents
SINAMICS DCM DC Converter
10 Operating Instructions, 12/2018, A5E34763375A
7.5.3.8 X540 auxiliary voltage for the digital inputs ......................................................................... 245
7.5.3.9 X541 bidirectional digital inputs/outputs .............................................................................. 246
7.5.3.10 X542 relay outputs ............................................................................................................... 247
7.5.4 Connection example ............................................................................................................ 248
7.5.5 Meanings of the LEDs on the Terminal Module TM31 ........................................................ 249
7.5.6 Dimension drawing .............................................................................................................. 250
7.5.7 Installation ............................................................................................................................ 251
7.5.8 Protective conductor connection and shield support ........................................................... 252
7.5.9 Connector coding ................................................................................................................. 253
7.5.10 Technical data ...................................................................................................................... 254
7.6 Terminal Module TM150 ...................................................................................................... 255
7.6.1 Description ........................................................................................................................... 255
7.6.2 Safety instructions ................................................................................................................ 256
7.6.3 Interface description ............................................................................................................. 257
7.6.3.1 Overview .............................................................................................................................. 257
7.6.3.2 X500 and X501 DRIVE-CLiQ interfaces .............................................................................. 258
7.6.3.3 X524 Electronics power supply ............................................................................................ 259
7.6.3.4 X531-X536 temperature sensor inputs ................................................................................ 259
7.6.4 Connection examples .......................................................................................................... 261
7.6.5 Meaning of the LEDs on the Terminal Module TM150 ........................................................ 263
7.6.6 Dimension drawing .............................................................................................................. 264
7.6.7 Installation ............................................................................................................................ 265
7.6.8 Protective conductor connection and shield support ........................................................... 266
7.6.9 Technical data ...................................................................................................................... 267
8 Commissioning .................................................................................................................................... 269
8.1 Commissioning checklist ...................................................................................................... 270
8.1.1 Commissioning checklist ...................................................................................................... 270
8.2 Switching on ......................................................................................................................... 272
8.3 Commissioning using the BOP20 operator panel ................................................................ 273
8.3.1 Preconditions ....................................................................................................................... 273
8.3.2 Commissioning steps ........................................................................................................... 274
8.4 Commissioning using the AOP30 operator panel ................................................................ 281
8.4.1 First commissioning ............................................................................................................. 281
8.4.1.1 First power-up ...................................................................................................................... 281
8.4.1.2 Full drive commissioning ...................................................................................................... 283
8.4.2 Status after commissioning .................................................................................................. 286
8.4.3 Resetting parameters to factory settings ............................................................................. 287
8.5 Commissioning with the STARTER commissioning tool ..................................................... 287
8.5.1 STARTER commissioning tool ............................................................................................. 287
8.5.1.1 Installing the STARTER commissioning tool ....................................................................... 288
8.5.1.2 Layout of the STARTER user interface ............................................................................... 288
8.5.2 Procedure for commissioning with STARTER ..................................................................... 289
8.5.2.1 Creating the project .............................................................................................................. 289
8.5.2.2 Configuring a drive unit ........................................................................................................ 298
8.5.2.3 Starting the drive project ...................................................................................................... 317
8.6 Activating function modules ................................................................................................. 321
8.6.1 Activating offline with STARTER .......................................................................................... 321
8.6.2 Activating online through parameters .................................................................................. 323

Siemens SINAMICS Series Specifications

General

Product Line	SINAMICS
Cooling Method	Air-cooled, Liquid-cooled
Voltage Range	200 V to 690 V
Power Range	0.12kW - 250kW
Communication Interfaces	PROFINET, PROFIBUS, Ethernet
Control Modes	Vector control, V/f control
Protection Class	IP20
Type	Variable Frequency Drives (VFD)