Need help?Do you have a question about the Siemens SITRANS FUS080 and is the answer not in the manual?
General| Type | Ultrasonic flow meter |
|---|---|
| Power Supply | 24 V DC |
| Measurement Principle | Transit time difference |
| Accuracy | ±0.5% of reading |
| Output Signal | 4 to 20 mA, pulse |
| Communication | HART |
| Pressure Rating | 16 bar |
| Temperature Range | -40°C to +160°C |
Lists components included with the SITRANS FUS080 transmitter and SONOKIT.
Checks to perform before installing the flowmeter.
Explains the transmitter and system nameplates and their components.
Describes the purpose and use of the application label.
Details changes in documentation across editions and firmware versions.
Provides details on finding product information on the internet and worldwide contact.
Mentions compliance with national regulations and EN 60079-14.
States device safety requirements must be observed for its expected life.
Explains the meaning of the CE mark and its associated guidelines.
Discusses potential hazards of lithium batteries and basic precautions.
Informs about the availability of certificates online and on CD.
Lists typical applications for the flowmeters.
Details the components included in the SITRANS F US SONOKIT system.
Explains MODBUS RTU communication via IrDA and optional modules.
Lists key features like power options, pipe diameter suitability, and enclosure rating.
Explains the physical principle of ultrasonic flow measurement.
Notes on suitability for indoor/outdoor, temperature specs, and enclosure rating.
Warnings about electrical connections and qualified personnel.
Guidelines for cable length, routing, and type for IP67 rating.
Explains the procedure for connecting transducer cables, including grounding.
Outlines the three steps for wiring power and output.
Instructions for wiring power supply, with a warning.
Explains how to wire pulse outputs and notes on EMC performance.
Steps for tightening cable glands and mounting the transmitter.
Describes the three areas of the local display and information symbols.
Details how to navigate menu items using the push button.
Outlines the steps for device power-up and battery status reset.
Introduces SIMATIC PDM and its role in configuration.
Steps for connecting the IrDA adapter to PC and mounting it on the FUS080.
Covers installing driver, adding device to network, and configuring device.
Process for reading parameters and managing device data via PDM.
Instructions for using the "Pipe geometric assistant" and defining sensor parameters.
Setting Pulse Output A and Qmax for system optimization.
Downloading parameters and verifying device operation.
Instructions for saving settings to PC and generating a qualification certificate.
Steps to generate and access the qualification certificate.
How to change units for totalizer and flow rate displays.
Explains password protection for MODBUS communication and how to change it.
Explains the use of a hardware jumper (HW key) to access protected parameters.
States the device is maintenance-free but requires periodic inspection.
Recommends battery replacement and discusses lifetime.
Step-by-step instructions for replacing the battery pack.
Provides contact info for tech support and online resources.
Information for service requests and device return process.
Guidelines for battery and general electronic equipment disposal.
Explains how the device provides error codes and where to view them.
Table of error codes, their causes, and remedies.
How to use SIMATIC PDM for diagnosing the device and viewing process values.
Graph showing gain step vs. transducer distance for diagnostics.
Details gain step and flow velocity error conditions for diagnostics.
Technical specifications of the SITRANS FUS080 transmitter.
Details on battery types, consumption, and operation time calculation.
Specifies required sensor-specific data for measurement accuracy.
Provides dimensional drawings and specifications for the transmitter.
How to create and use the qualification certificate.
Forms and fields for the qualification certificate.
Service/Diagnostic, Comments, and completion status for the certificate.
Lists identification parameters with Modbus address, default value, and description.
Lists output parameters with Modbus address, default value, and description.
Lists diagnostic parameters including fault status and reset functions.
Lists parameters related to meter setup, calibration, and filters.
Lists parameters related to pipe data such as number of paths and diameter.
Lists parameters for decimal point and operator menu settings.
Details factory configurations for 1-path and 2-path SONOKIT.
Default settings for MODBUS communication parameters.
Template for sensor geometry measurement report for 2-path systems.
Table of dimension-dependent settings for SONOKIT 2-path systems.
Table of dimension-dependent settings for SONOKIT 1-path systems.
Information on obtaining the latest ordering data.
To Next Page