Why Siemens SITRANS FUE1010 IP65 NEMA 4X Measuring Instruments shows - - -F- - - Fault Alarm?
The '- - -F- - - Fault Alarm' on Siemens Measuring Instruments indicates a loss of signal strength (ALC) or a change of Rx signal location (Beam Blowing). You can try to recouple sensors with fresh couplant or install sensors in Direct mount mode. If the problem persists, further assistance may be needed.
How to fix memory full on Siemens Measuring Instruments?
If you see a 'Memory Full!' message when trying to save site data on your Siemens Measuring Instruments, it means the data memory is full. To resolve this, delete an obsolete site or clear the Data-logger memory to create space for the new data.
What to do if Siemens SITRANS FUE1010 IP65 NEMA 4X Measuring Instruments shows low signal?
If your Siemens Measuring Instruments displays a 'Low Signal' message, it indicates that the receive signal is insufficient for proper operation. This could be due to several reasons: * Invoking [Install Complete] on an empty pipe. * Insufficient or evaporated coupling compound. * A disconnected or broken sensor cable. * The pipe needs conditioning at the mounting location. * Large air bubbles. * Defective sensor cables or incorrect channel connections. * The Set Empty routine performed when the pipe was NOT actually empty. If you correct the problem, press to resume the installation. Otherwise, abort the installation and investigate.
Why Siemens Measuring Instruments says Chan Not Setup?
If your Siemens Measuring Instruments displays 'Chan Not Setup', it means you're trying to use a channel that isn't enabled. To fix this, enable the channel in the [Channel Setup - Channel Enable - Yes] menu. Remember, a channel can only be enabled after an 'Install' operation is completed.
What does mean on Siemens SITRANS FUE1010 IP65 NEMA 4X?
The '' message on your Siemens Measuring Instruments appears when you request Data-logger data output to the printer or Graphics screen, but no Datalogger data exists, or it signifies the end of a transmitted file. To resolve this, set up the Datalogger.
What to do if Siemens SITRANS FUE1010 IP65 NEMA 4X Measuring Instruments displays Invalid Setup (use Direct Mode)?
If your Siemens Measuring Instruments displays 'Invalid Setup (use Direct Mode)', the system has detected invalid sensor spacing, erroneous liquid pipe parameters, or another factor preventing the Initial Makeup. This may be due to an out-of-range data entry or an invalid condition, such as overlapping sensors in Reflect Mode. If selecting Direct Mode doesn't resolve the issue, review all site setup and sensor installation choices, especially the data entered for the pipe and liquid. In Reflect Mode, if the flow meter detects that the pipe wall signal may infringe upon the liquid signal, use Direct Mode instead. You can abort the install routine by pressing the appropriate keys and continue programming other site data while you resolve the issue.
What does Clr Active Memory mean on Siemens Measuring Instruments?
The 'Clr Active Memory?' message on Siemens Measuring Instruments appears when you press and hold the F4 key during power-up. Use the F4 function to restore operation if a severe event, like a power surge, disrupts system operation.
What does Re-space Index mean on Siemens SITRANS FUE1010 IP65 NEMA 4X Measuring Instruments?
The 'Re-space Index' message on Siemens Measuring Instruments means the measured liquid sonic velocity (Vs) is more than +/- 25% of the average Vs range. To solve this: * Ensure proper pipe dimensions and/or Liquid data entries are correct. * Enter the correct Sensor Size into the meter [Install Sensor] menu. * Confirm sensor spacing is correct by checking [Install Sensor] menu spacing parameters.
Why Siemens Measuring Instruments displays No Sites - Press ?
If your Siemens Measuring Instruments displays 'No Sites - Press ', it means you're trying to recall or delete a site setup when no sites are stored. To resolve this, create a site.
What does Security mean on Siemens SITRANS FUE1010 IP65 NEMA 4X?
The 'Security' message on Siemens Measuring Instruments appears when changing previously entered data while the security switch is in the [Disable] position, or if a security code has been entered. To resolve this: * Change the switch position to [Enable]. * Enter the previously set security code.
General| Measurement Principle | Ultrasonic |
|---|---|
| Power Supply | 24 V DC |
| Communication Protocol | HART |
| Category | Measuring Instruments |
| Protection Class | IP65 NEMA 4X |
| Output Signal | 4-20 mA |
| Operating Temperature | -40 to +70 °C |
| Housing Material | Aluminum |
| Temperature Range | -40°C to +70°C |
| Display | LCD |
Brief overview of the manual's content and audience.
Lists the components included with the device for installation.
Provides information about changes in previous document versions.
Guides users to additional resources for more details.
Outlines crucial safety guidelines for proper operation and maintenance.
Explains various symbols used to denote potential hazards.
Details relevant regulations and standards the device must comply with.
Provides safety information regarding the handling and use of lithium batteries.
Covers specific safety requirements and approvals for hazardous environments.
Reiterates important safety precautions and classifications for hazardous locations.
Highlights the key functionalities and technological aspects of the FUE1010.
Describes the transmitter's capabilities and certifications for specific environments.
Lists typical uses and industries where the flow meter is applied.
Explains the underlying principles and technology behind the flow measurement.
Outlines critical safety measures to be taken before and during installation.
Provides guidance on selecting the optimal position for sensor and transmitter installation.
Emphasizes the importance of adhering to technical limits and guidelines.
Offers basic requirements and best practices for successful sensor placement.
Details the procedures for physically attaching the transmitter unit.
Crucial safety warnings and precautions for electrical connections, especially in hazardous areas.
Step-by-step instructions for wiring the transmitter, including power and sensor connections.
Instructions on how to access and navigate the device's menu system.
Detailed steps for configuring the flow meter settings, including language, units, and site data.
Comprehensive guide on installing sensors using different mounting modes (Reflect, Direct).
Procedures for compensating for zero offset in flow measurements.
Details on how to install temperature sensors for accurate readings.
Final steps for connecting the sensors to the transmitter.
Pre-commissioning checks and requirements to ensure proper setup.
Procedure for setting the empty pipe alarm threshold and related routines.
Overview of the device's menu structure and navigation.
How to choose and configure units for flow rate and totalizer displays.
Configuration of output limits for various measurement parameters.
Setup and management of the device's data logging capabilities.
Fine-tuning operational parameters like damping and deadband for optimal performance.
Configuration of relay outputs for alarm and control functions.
Management of the device's memory for data storage.
Configuration of analog output signals for current, voltage, and pulse rate.
Setup of analog input signals for temperature and power consumption.
Procedure for activating artificial energy rate input for testing.
Fine-tuning analog outputs using external test equipment.
Procedures for calibrating temperature sensors against external standards.
Explanation and setup of the Reflexor operating mode for Doppler flow detection.
Lists and explains various alarm codes displayed by the flow meter.
Guidelines for periodic inspection and maintenance of the device.
Information on how to contact Siemens for technical assistance.
Steps and requirements for returning the product for service or repair.
Information on the proper disposal of batteries according to regulations.
General tips and solutions for common errors and messages.
Steps for performing a system reset using the F4 key sequence.
Detailed guide on using the graphical display for diagnostics and troubleshooting.
Explanation of data related to sensor characteristics and operation for troubleshooting.
Procedure for forcing a transmit condition for diagnostic purposes.
Provides specifications for operating temperature, degree of protection, and performance metrics.
Information on available certificates for the device.
Guidance on obtaining the latest ordering data.
Detailed diagrams and tables for I/O connections and wiring configurations.
Instructions for connecting the flow meter to a PC via RS-232.
Methods and tables for calibrating the flowrate output.
Lists various installation and outline drawings for different components and configurations.
To Next Page