Table of contents
ULTRAMAT 23
Manual, 3/2016, A5E37100388-003
7
7.3.1 Display and operator panel ..................................................................................................... 91
7.3.2 User interface .......................................................................................................................... 93
7.3.3 Key assignments ..................................................................................................................... 94
7.4 Operating modes .................................................................................................................... 94
7.4.1 Warm-up phase ...................................................................................................................... 95
7.4.2 Measuring mode ..................................................................................................................... 96
7.4.3 Input mode .............................................................................................................................. 96
7.4.3.1 Code levels ............................................................................................................................. 97
7.4.3.2 Key operations step by step ................................................................................................... 98
7.4.3.3 The ESC key ......................................................................................................................... 101
7.4.3.4 The CAL key ......................................................................................................................... 101
7.4.3.5 The PUMP key ...................................................................................................................... 102
8 Functions ............................................................................................................................................ 103
8.1 Diagnostics ........................................................................................................................... 103
8.1.1 Diagnostics: Status ............................................................................................................... 104
8.1.1.1 Analyzer status: Status: Logbook/faults ................................................................................ 104
8.1.1.2 Analyzer status: Status: Maintenance request ..................................................................... 105
8.1.1.3 Analyzer status: Status: AUTOCAL deviation ...................................................................... 105
8.1.1.4 Analyzer status: Status: O2 sensor status ............................................................................ 106
8.1.1.5 Analyzer status: Status: H2S sensor status.......................................................................... 106
8.1.2 Diagnostics: Diagnostics values ........................................................................................... 107
8.1.2.1 Analyzer status: Diagnostics values: IR ................................................................................ 107
8.1.2.2 Analyzer status: Diagnostics values: (Electrochemical) O2 sensor ..................................... 108
8.1.2.3 Analyzer status: Diagnostics values: (Paramagnetic) O2 sensor ......................................... 108
8.1.2.4 Analyzer status: Diagnostics values: H2S sensor ................................................................ 109
8.1.2.5 Diagnostics: Diagnostics values: Pressure sensor ............................................................... 109
8.1.2.6 Analyzer status: Diagnostics values: Other diagnostics values ........................................... 109
8.1.3 Analyzer status: Factory settings hardware .......................................................................... 110
8.1.4 Analyzer status: Factory settings software ........................................................................... 110
8.2 Calibration ............................................................................................................................. 111
8.2.1 Calibration ............................................................................................................................. 111
8.2.2 Calibration: Infrared measuring range .................................................................................. 112
8.2.2.1 Calibration: Infrared measuring range: Set span gas values................................................ 113
8.2.2.2 Calibration: Infrared measuring range: Start with Range MR 1/2 ......................................... 113
8.2.3 Calibration: Electrochemical oxygen measuring range ........................................................ 114
8.2.3.1 Calibration: O2 measuring range: Sensor inst. date ............................................................. 114
8.2.3.2 Calibration: O2 measuring range: Calibrating the O2 zero point .......................................... 115
8.2.3.3 Calibration: O2 measuring range: Calibrate measuring range ............................................. 115
8.2.4 Calibration: Paramagnetic oxygen sensor ............................................................................
116
8.2.4.1 Calibration: O2 paramagnetic: Calibrating the zero point ..................................................... 117
8.2.4.2 Calibration: O2 paramagnetic: Calibrating the measuring range ......................................... 117
8.2.5 Calibration: H2S sensor ........................................................................................................ 118
8.2.5.1 Calibration: H2S sensor: Defining the installation ................................................................ 119
8.2.5.2 Calibration: H2S sensor: Calibrating the zero point .............................................................. 119
8.2.5.3 Calibration: H2S sensor: Calibrating the measuring range .................................................. 119
8.2.5.4 Calibration: H2S sensor: Enter TC parameters .................................................................... 120
8.2.6 Calibration: Pressure sensor ................................................................................................ 121
8.2.7 Calibration: AUTOCAL/drift values ....................................................................................... 122
8.2.7.1 Calibration: AUTOCAL/drift values: Drift values ................................................................... 122
8.2.7.2 Calibration: AUTOCAL/drift values: Cycle time .................................................................... 123
To Next Page
Loading...
