What to do if my SNBC Printer stops printing and warns errors during printing?
If your SNBC Printer stops printing and indicates errors during printing, it might be due to the paper running out or paper jammed in the cutter. Install a new paper roll and check the cutter path for any obstructions.
Why is the printout from my SNBC BT-T080R Printer not clear?
If the printout from your SNBC Printer is not clear, it could be due to several reasons. Ensure the paper roll is loaded correctly and that you are using the recommended paper or its equivalent. The print head may need cleaning, or the print darkness may need adjustment. Also, verify that you are using a power supply that meets the printer's requirements.
What to do if my SNBC Printer doesn’t work after receiving commands?
If your SNBC Printer isn't working after receiving commands, it may be in an error status, the communication cable might not be connected properly, or the interface setting could be incorrect. You should clear any errors, ensure the communication cable is correctly connected, print a self-test page, and then set the interface again according to the information on the self-test page.
Why SNBC BT-T080R can’t feed paper automatically?
If your SNBC Printer can’t feed paper automatically, it could be due to an irregular paper head, paper jams, or the paper loading sensor not being fully covered by the paper head. Trim the paper head as needed, remove any jammed paper, and ensure the front head of the paper fully covers the paper loading sensor.
Why LED isn’t light and printer doesn’t work (SNBC)?
If the LED on your SNBC Printer isn’t lit and the printer isn’t working, ensure the printer is correctly connected to the power supply and that the printer is turned on.
What to do if the paper can’t be ejected out smoothly from SNBC Printer?
If the paper in your SNBC Printer can’t be ejected out smoothly, it's likely due to paper jams. Check the paper path, remove any wastepaper, and then reload the paper.
What to do if the paper doesn’t stop at the normal print position after loading paper automatically with SNBC Printer?
If, after loading paper automatically, the paper doesn’t stop at the normal print position on your SNBC Printer, the paper loading sensor may be covered by dust or wastepaper. Clean the paper loading sensor.
Why paper roll can’t be loaded onto paper holder smoothly in SNBC BT-T080R Printer?
If the paper roll can’t be loaded onto the paper holder smoothly in your SNBC Printer, it's likely that the paper roll core ID does not match the printer. Replace the print paper.
Items shall be strictly followed to avoid injury or damage to body and equipment.
Items with important information and prompts for operating the printer.
Important warnings regarding printer operation and safety to prevent injury or damage.
Important guidelines and prompts for operating the printer safely and effectively.
Overview of the BT-T080R printer's capabilities and applications.
Key characteristics and functionalities of the BT-T080R printer.
Detailed technical parameters and specifications of the printer.
Specific technical details related to the printer's cutting mechanism.
Information on sensors and methods used for detecting printer status.
Technical specifications related to the paper used for printing.
Details on the positioning of print and cut operations.
General overview of the printer's physical appearance and its modules.
Dimensions and physical size specifications of the printer.
Description of the printer's buttons and LED status lights.
Details on the optional paper outlet module.
Information on the optional anti-pull and anti-jam module.
Content and information found on the product label.
Steps for unpacking the printer and checking contents.
Instructions for installing the main print mechanism of the printer.
Guidance on installing the cantilever module, including buffer module.
Installation details for cantilever angle at 0 degrees.
Installation details for cantilever angle at 30 degrees.
Installation details for cantilever angle at 60 degrees.
Installation details for cantilever angle at 90 degrees.
Installation details for cantilever angle at -30 degrees.
Installation details for cantilever angle at -60 degrees.
Instructions for installing the paper roll baffle.
Steps for connecting the paper near end sensor.
Procedures for adjusting the paper near end sensor for accurate detection.
How to connect the printer to the AC power source.
Instructions for connecting communication interface cables.
Steps for correctly installing a paper roll into the printer.
Procedures for loading paper into the print path.
Standard procedure for installing the printer driver.
Alternative method for installing the printer driver with advanced options.
Steps for connecting the paper near end sensor.
Procedures for adjusting the paper near end sensor for accurate detection.
Steps for correctly installing a paper roll into the printer.
Procedures for loading paper into the print path.
Standard procedure for installing the printer driver.
Alternative method for installing the printer driver with advanced options.
How to clean the printer's critical print head and platen roller.
Instructions for cleaning the paper near end sensor.
Details on the RS-232 serial interface and its parameters.
Information regarding the USB interface and its specifications.
Guide to identifying and resolving common printer errors.
Practical solutions for various problems encountered during operation.
Information on how to print and interpret the printer's self-test page.
Introduction to utility software for printer configuration and monitoring.
General| Print Method | Direct Thermal |
|---|---|
| Print Width | 72 mm |
| Resolution | 203 dpi |
| Interface | USB+Serial+LAN |
| Paper Width | 80 mm |
| Power Supply | DC 24V/2.5A |
| Weight | 1.2 kg |
| Paper Thickness | 0.06 to 0.08 mm |
| Auto Cutter | Full and Partial Cut |
To Next Page
