SPI Lasers redPOWER QUBE

To Next Page

To Previous Page

Commercial in Confidence

SM-S00500 Revision A 21 October 2016

redPOWER QUBE Cased Fiber Laser User Manual

Figure 44 Moving to STANDBY in Remote Control

(Ramp down time configured)

Figure 45 Moving to ON state in Remote Control

before the state has moved to the STANDBY state

Main Page

Default Chapter5
- Table of Contents5
1 Structure and Scope of These Instructions for Use11
2 Definition of Symbols and Terms12
3 Health and Safety13
- General13
- Intended Use of the QUBE Fiber Laser14
- Hazards14
- Compliance16
- Figure 1 WEEE Symbol16
- Labelling18
- Table 1 Safety, Explanatory and Compliance Labels18
- Table 2 Information Labels19
4 Document References20
5 Redpower QUBE Product Tour20
- Figure 2 Redpower QUBE Cased Fiber Laser Key Parts21
- Key Parts21
- Figure 4 QUBE Cased Fiber Laser Key Features23
- Key Features23
6 Getting Started32
- Receiving and Inspection32
- Unpacking and Handling32
- Figure 8 QUBE Fiber Laser in Packing Case as Received33
- Figure 11 Bubble Wrap and Top Foam Block Removed33
- Unpacking the Beam Delivery Optic34
- Figure 12 Four Point Sling Attached34
- Figure 13 QUBE Fiber Laser on Trolley34
7 Installation35
- Safety and Compliance During Installation35
- Location and Environment35
- Mounting36
- Cooling Water Connections36
- Figure 15 Cooling Water Connections to QUBE Fiber Laser37
- Table 4 Water Tubing38
- Table 5 Water Tubing38
- Fiberview Installation39
- Table 6 Laser Integrator Supplied PC - for Operating Fiberview39
- Electrical Connections40
- Figure 16 Interface Connectors41
- Table 7 Interface Connectors41
- Table 8 Electrical Supply Cord Wire Sizes42
- Figure 17 Internal Connections for Electrical Supply43
- Table 9 Serial Port Connections43
- Table 10 PL5 Machine Interface Pin out45
- Figure 18 Machine Interface Connections Circuits46
- Figure 19 PL5 Programmable Inputs47
- Figure 20 PL5 Programmable Outputs48
- Table 11 Laser Inputs49
- Table 12 Laser Status Outputs51
- Figure 21 Connections to PL8154
- Figure 22 Typical Connections to PL82 (Control Contact and Indicator Lamps)56
- Figure 23 Typical Connections to PL82 (PLC)57
- Figure 24 Timing Diagram58
- Figure 25 Typical Connections to PL9159
- Figure 26 a Typical Connection to PL9660
- Figure 27 a Typical Connection to PL9861
- Routing the Beam Delivery Optic63
- Connecting and Disconnecting the PIPA-Q Optical Connector64
- Figure 29 PIPA-Q with Protective Cap65
- Figure 30 Connector before Removal of Protective Tape66
- Figure 31 Red Dots Aligned66
- Figure 32 Connector Inserted into Receiver67
8 Operating Instructions68
- Before Operation68
- Powering the QUBE Fiber Laser on and off69
- Control of Operating Temperature69
- Alarms and Warnings70
9 Laser Control and Fiberview71
- Overview71
- Basic Operation71
- Figure 33 Fiber Laser Connection Dialog72
- Figure 34 Fiberview Overview Screen73
- Parameter Sets74
- Table 14 Parameter Set Attributes74
- Figure 35 Fiberview Parameter Editor76
- Process Cycles78
- Other Settings80
- Table 15 Process Cycle Step Attributes80
Basic Control Using Serial Communication82
- Overview82
- Functionality83
- Basic Serial Communication Protocol Message References85
Machine Interface Reference85
- Overview85
- Default Input Functionality86
- Table 16 Default Configuration of Machine Interface Inputs86
- Table 17 Default Configuration of Machine Interface Outputs86
- Default Output Functionality107
- Machine Interface Protocol Message References112
Alarm and Warning Messages113
- Alarm Code Definitions113
- Warning Code Definitions115
Maintenance118
- Periodic Inspection118
- General Cleaning118
- Cleaning Optics119
Disposal119
General Information119
- Trade Marks119
- Licensing119
- Software119
- Table 18 Replacement Windows119
- Warranties120
- Copyright120
- Changes120
Contact Information121
General Specifications121
- Table 19 Contact Information121
- Operating Conditions122
- Table 20 Environmental Operating Conditions122
- Non-Operating Conditions123
- Table 21 Non-Operating Conditions123
- Utility Requirements124
- Table 22 Electrical Requirements124
- Table 23 Power Consumption124
- Table 24 Cooling Water Requirements125
- Table 25 Cooling Requirements (Connection to Manifold)125
Optical Specifications126
- General Optical Specifications126
- Table 23 Required Chiller Capacity126
- Table 26 Cooling Requirements (Connection to PIPA-Q Optical Connector)126
- Table 27 General Optical Specifications126
- Optical Output - PIPA-Q Optical Connector127
- Table 28 Single Mode Optical Specifications127
- Table 29 50ΜM Multimode Optical Specifications127
Mechanical Specifications128
- Overall Dimensions and Masses128
- Table 30 100ΜM Multimode Optical Specifications128
- Table 31 Case Lengths128
- PIPA-Q Optical Connector130
- Table 32 Mechanical Specifications - PIPA-Q Optical Connector130
Customer Service131

SPI Lasers redPOWER QUBE - Page 93

Table of Contents