Steris Harmony LED Wall Control Unit - Figure 4-3. Monitor Arms Positioning

74 pages

Save Page as PDF

To Next Page

To Previous Page

4-3

Post Installation Verification Operator Manual 10083002

Figure 4-3. Monitor Arms Positioning

320°

10° UP

10° DN

320°

15° UP

90° DN

15° UP

90° DN

10° UP

10° DN

10° UP

10° DN

Finished Floor

10° Clockwise

10° Counterclockwise

10° Clockwise

10° Counterclockwise

Main Page

Table of Contents5
Safety Precautions11
Table 1-1. System Laser Components12
Symbol Definitions15
Table 2-1. Symbol Definitions15
Product Performance19
Lighthead Optical Performance19
Table 3-1. M5 Lighthead and M7 Lighthead Optical Performance19
Environmental Conditions20
Power Requirements20
Post Installation Verification21
Pre-Operation Checklist21
Figure 4-1. Tension Screw Location for Harmony Spring Arms21
Check Suspension Movement22
4.3 Monitor Arms22
Figure 4-2. Check Suspension22
Figure 4-3. Monitor Arms Positioning23
Check System Operation24
Figure 4-4. Use Control Center to Check System Operation24
Check Optional Video Camera Module Operation25
Figure 4-5. Check Lighthead Intensity Operation Using Surgeon's Control Buttons25
Figure 4-6. in Light Video Camera High-Definition Model Shown26
Figure 4-7. Camera Control Menus27
Check Optional Monitor Support Arms28
Figure 4-8. Monitor Support Arm (Typical Dual Flat Panel Monitor Arm Shown)28
Operating Instructions29
5.1 Intensity Controls29
Figure 5-1. Harmony Control Center Light Control Screen for Harmony LED System29
Figure 5-2. Lighthead Surgeon's Control Buttons30
Lighthead Features31
Figure 5-3. Harmonyair Surgical Lighting System M Series Lighthead31
Table 5-1. Harmony Lighthead Features31
Lighthead Fault Indications32
Control Center Fault Indication32
5.4.1 Fault Display32
Figure 5-4. Lighthead Exterior LED Indicator32
Figure 5-5. Harmony Control Center Fault Display32
Control Center Fault Log Indications33
Table 5-2. Control Center Fault Indications33
Figure 5-6. M5 and M7 Lighthead Positioning35
Harmony Lighthead Pattern Adjustment36
Figure 5-7. Light Pattern Size Adjustment36
5.7 Lighthandles37
Plastic Lighthandle and Disposable Lighthandle Cover37
Sterilizable Surgeon Control Handle37
Figure 5-8. Standard Handle39
5.8 Monitor Arms40
Figure 5-9. Sterilizable Surgeon Control Handle40
Install Flat Panel Monitor Yoke Handle Disposable Sterile Covers43
Figure 5-12. Installing Disposable Sterile Monitor Handle Covers (Current Production Handles)43
Figure 5-13. Installing Disposable Sterile Monitor Handle Covers (Out-Of-Production Handles)44
Video Camera Module Installation or Removal45
Figure 5-14. Install Optional Camera Module (SD Model Shown)45
Install Camera Disposable Sterile Cover46
5.12 Video Camera46
Figure 5-15. Install Camera Disposable Sterile Cover46
Table 5-3. Camera Functions47
5.12.1 Camera Operation48
Figure 5-16. Camera Control Menus 1 and 2 (HD or SD Camera Modules)48
Table 5-4. Camera Control Screen 4 - Speed Adjustment Operation50
Figure 5-17. Camera Control Menus 3 (HD or SD Camera Modules)51
Figure 5-18. Camera Control Menu 4 (HD or SD Camera)51
5.12.2 HD Settings52
Table 5-5. Camera Control Screen 4 - HD Video Signal Adjustment Operation52
Guidelines for Maximizing Video Image53
5.12.4 Engage Manual Focus53
5.13 System Standby54
Ambient Light Fixture54
Ambient Light Operation Overview54
Figure 5-19. System Standby Screen54
Configuring and Using the Ambient Light55
Figure 5-20. System Menu55
Figure 5-21. Configure Ambient Light55
ACT Enabled System57
Figure 5-22. Activate ACT Enabled System57
Lighthead Runtime and Limit Values58
Figure 5-23. System Menu 2 (Runtime and Limit Values)58
Cleaning the Equipment59
Cleaning Equipment59
General Cleaning/Disinfecting Procedure60
Figure 6-1. Areas to be Cleaned61
Areas to be Cleaned before each Use62
Operator Troubleshooting63
Preventive Maintenance65
Inspect Suspension65
Inspect Control Center65
Maintenance65
Replacement Parts67
Waste Management Guidelines69
Appendix - EMC Compliance Technical Data71
Table 11-1. Guidance and Manufacturer's Declaration - Electromagnetic Emissions - for All ME Equipment71
And ME Systems (Per IEC 60601-1-2 Clause 5.2.2.1 C) Table 1)71
Table 11-2. Guidance and Manufacturer's Declaration - Electromagnetic Immunity for All ME Equipment and  ME Systems72
Table 11-3. Guidance and Manufacturer's Declaration - Electromagnetic Immunity for ME Equipment and  ME Systems that Are Not Life-Supporting73
Table 11-4. Recommended Separation Distances between Portable and Mobile RF Communications74
Equipment and the Harmonyair Surgical Lighting System M Series74

Steris Harmony LED Wall Control Unit - Figure 4-3. Monitor Arms Positioning

Table of Contents

Related product manuals