Steris Harmony LED Wall Control Unit - Symbol Definitions

74 pages

Save Page as PDF

To Next Page

To Previous Page

2-1

Symbol Definitions Operator Manual 10083002

The following symbols appear on the HarmonyAIR™ Surgical Lighting System M Series with Harmony

LED Wall

Control Unit.

Table 2-1. Symbol Definitions

Symbol Definition

Standby

Turn System ON

Turn System OFF

Lighthead (designation and intensity) Symbol Definitions

LED Module Failure

Protective Earth (Ground)

Pinch Point Label

Attention, consult manual for further instructions

SYMBOL DEFINITIONS

Main Page

Table of Contents5
Safety Precautions11
Table 1-1. System Laser Components12
Symbol Definitions15
Table 2-1. Symbol Definitions15
Product Performance19
Lighthead Optical Performance19
Table 3-1. M5 Lighthead and M7 Lighthead Optical Performance19
Environmental Conditions20
Power Requirements20
Post Installation Verification21
Pre-Operation Checklist21
Figure 4-1. Tension Screw Location for Harmony Spring Arms21
Check Suspension Movement22
4.3 Monitor Arms22
Figure 4-2. Check Suspension22
Figure 4-3. Monitor Arms Positioning23
Check System Operation24
Figure 4-4. Use Control Center to Check System Operation24
Check Optional Video Camera Module Operation25
Figure 4-5. Check Lighthead Intensity Operation Using Surgeon's Control Buttons25
Figure 4-6. in Light Video Camera High-Definition Model Shown26
Figure 4-7. Camera Control Menus27
Check Optional Monitor Support Arms28
Figure 4-8. Monitor Support Arm (Typical Dual Flat Panel Monitor Arm Shown)28
Operating Instructions29
5.1 Intensity Controls29
Figure 5-1. Harmony Control Center Light Control Screen for Harmony LED System29
Figure 5-2. Lighthead Surgeon's Control Buttons30
Lighthead Features31
Figure 5-3. Harmonyair Surgical Lighting System M Series Lighthead31
Table 5-1. Harmony Lighthead Features31
Lighthead Fault Indications32
Control Center Fault Indication32
5.4.1 Fault Display32
Figure 5-4. Lighthead Exterior LED Indicator32
Figure 5-5. Harmony Control Center Fault Display32
Control Center Fault Log Indications33
Table 5-2. Control Center Fault Indications33
Figure 5-6. M5 and M7 Lighthead Positioning35
Harmony Lighthead Pattern Adjustment36
Figure 5-7. Light Pattern Size Adjustment36
5.7 Lighthandles37
Plastic Lighthandle and Disposable Lighthandle Cover37
Sterilizable Surgeon Control Handle37
Figure 5-8. Standard Handle39
5.8 Monitor Arms40
Figure 5-9. Sterilizable Surgeon Control Handle40
Install Flat Panel Monitor Yoke Handle Disposable Sterile Covers43
Figure 5-12. Installing Disposable Sterile Monitor Handle Covers (Current Production Handles)43
Figure 5-13. Installing Disposable Sterile Monitor Handle Covers (Out-Of-Production Handles)44
Video Camera Module Installation or Removal45
Figure 5-14. Install Optional Camera Module (SD Model Shown)45
Install Camera Disposable Sterile Cover46
5.12 Video Camera46
Figure 5-15. Install Camera Disposable Sterile Cover46
Table 5-3. Camera Functions47
5.12.1 Camera Operation48
Figure 5-16. Camera Control Menus 1 and 2 (HD or SD Camera Modules)48
Table 5-4. Camera Control Screen 4 - Speed Adjustment Operation50
Figure 5-17. Camera Control Menus 3 (HD or SD Camera Modules)51
Figure 5-18. Camera Control Menu 4 (HD or SD Camera)51
5.12.2 HD Settings52
Table 5-5. Camera Control Screen 4 - HD Video Signal Adjustment Operation52
Guidelines for Maximizing Video Image53
5.12.4 Engage Manual Focus53
5.13 System Standby54
Ambient Light Fixture54
Ambient Light Operation Overview54
Figure 5-19. System Standby Screen54
Configuring and Using the Ambient Light55
Figure 5-20. System Menu55
Figure 5-21. Configure Ambient Light55
ACT Enabled System57
Figure 5-22. Activate ACT Enabled System57
Lighthead Runtime and Limit Values58
Figure 5-23. System Menu 2 (Runtime and Limit Values)58
Cleaning the Equipment59
Cleaning Equipment59
General Cleaning/Disinfecting Procedure60
Figure 6-1. Areas to be Cleaned61
Areas to be Cleaned before each Use62
Operator Troubleshooting63
Preventive Maintenance65
Inspect Suspension65
Inspect Control Center65
Maintenance65
Replacement Parts67
Waste Management Guidelines69
Appendix - EMC Compliance Technical Data71
Table 11-1. Guidance and Manufacturer's Declaration - Electromagnetic Emissions - for All ME Equipment71
And ME Systems (Per IEC 60601-1-2 Clause 5.2.2.1 C) Table 1)71
Table 11-2. Guidance and Manufacturer's Declaration - Electromagnetic Immunity for All ME Equipment and  ME Systems72
Table 11-3. Guidance and Manufacturer's Declaration - Electromagnetic Immunity for ME Equipment and  ME Systems that Are Not Life-Supporting73
Table 11-4. Recommended Separation Distances between Portable and Mobile RF Communications74
Equipment and the Harmonyair Surgical Lighting System M Series74

Steris Harmony LED Wall Control Unit - Symbol Definitions

Table of Contents

Related product manuals