Steris Vision 1321 User Manual

920515770
Revision J
Vision® 1300 Series
Washer/Disinfector Models # 1321, # 1327 and #
1330L
Operator Manual

Steris Vision 1321 Specifications

General

Category	Medical Equipment
Model	Vision 1321
Manufacturer	Steris
Sterilization Temperature Range	121°C to 134°C
Sterilization Time	4 minutes
Power Requirements	208-240 VAC, 50/60 Hz, Single Phase, 20A
Door Type	Automatic
Cycle Options	Gravity, Liquid

Summary

Safety Precautions

General Safety Precautions

Warnings and cautions for personal injury and equipment damage.

Installation Verification

Voltage, Amperage, and Power Consumption

Installation Verification Checklist

Checklist to ensure complete and correct installation of the equipment.

Using Prolystica Ultra Concentrate Chemicals

Component Identification

Control System General Description

Operating Instructions

Before Operating Washer/Disinfector - General

Loading Washer/Disinfector

Typical Cycle Operation - General

General description of how a typical cycle operates.

Unloading Washer/Disinfector

Responding to a Warning Message

Responding to an Alarm

Stopping or Aborting a Cycle

Emergency Stop Pushbutton Procedure

Emergency Stop Cable Procedure

Cycle and Control Value Programming

Cycle and Control Value Programming - General

Logging in Supervisor Mode

Supervisor Mode Menus

Supervisor Menu - Supervisors

Supervisor Menu - Cycles: General

Modifying a Validated Cycle

Procedure for modifying parameters of validated cycles.

Copying/Creating a Customized Cycle

Procedure for creating customized cycles by copying existing ones.

Modifying a Customized Cycle

Procedure for modifying parameters of customized cycles.

Supervisor Menu - Machine Setup

Supervisor Menu - Reservoirs

Supervisor Menu - Transfer PDF Reports

Routine Maintenance

Routine Maintenance - General

Decontam Cycle Procedure

Traveler Spray Arm Assemblies Maintenance

Vision CW Instrument Washing Manifolded Rack Spray Arm Assemblies Maintenance

Emergency Stop Cables Testing

Emergency Stop Pushbuttons Testing

Troubleshooting

General Troubleshooting Guidelines

Alarm #1: Emergency Stop

Troubleshooting for the Emergency Stop alarm.

Alarm #2: Load Door Locking System Malfunction

Troubleshooting for load door locking system malfunctions.

Alarm #3: Unload Door Locking System Malfunction

Troubleshooting for unload door locking system malfunctions.

Alarm #4: Load Door Unlocked During Cycle

Troubleshooting for load door unlocking during a cycle.

Alarm #5: Unload Door Unlocked During Cycle

Troubleshooting for unload door unlocking during a cycle.

Alarm #6: Spray Arms Not Moving

Troubleshooting for spray arms that are not moving.

Alarm #7: Recirculation Process Malfunction

Troubleshooting for recirculation system malfunctions.

Alarm #8: Motor Overload Tripped

Troubleshooting for motor overload trips.

Alarm #9: Sump Draining/Recycling Malfunction

Troubleshooting for sump draining or recycling malfunctions.

Alarm #10: Water Recirculation Pressure Transmitter Defective

Troubleshooting for defective water recirculation pressure transmitters.

Alarm #11: Water Recycling Malfunction

Troubleshooting for water recycling malfunctions.

Alarm #12: Water Recirculation Temperature Too High

Troubleshooting for high water recirculation temperatures.

Alarm #13: Water Recirculation Too Long to Heat

Troubleshooting for water recirculation taking too long to heat.

Alarm #14: Water Recirculation RTD Defective

Troubleshooting for defective water recirculation RTD.

Alarm #15: Reservoir #1 Water Temperature Too High

Troubleshooting for high temperature in Reservoir #1.

Alarm #16: Reservoir #1 RTD Defective

Troubleshooting for defective Reservoir #1 RTD.

Alarm #17: Reservoir Overflow

Troubleshooting for reservoir overflow conditions.

Alarm #18: Reservoir #1 Hot Water Not Filling

Troubleshooting for Reservoir #1 not filling with hot water.

Alarm #19: Reservoir #1 Pure Water Not Filling

Troubleshooting for Reservoir #1 not filling with pure water.

Alarm #20: Reservoir #2 Hot Water Not Filling

Troubleshooting for Reservoir #2 not filling with hot water.

Alarm #21: Reservoir #2 Cold Water Not Filling

Troubleshooting for Reservoir #2 not filling with cold water.

Alarm #22: Reservoir #3 Hot Water Not Filling

Troubleshooting for Reservoir #3 not filling with hot water.

Alarm #23: Reservoir #1 Level Sensors Defective

Troubleshooting for defective level sensors in Reservoir #1.

Alarm #24: Reservoir #2 Level Sensors Defective

Troubleshooting for defective level sensors in Reservoir #2.

Alarm #25: Reservoir #3 Level Sensors Defective

Troubleshooting for defective level sensors in Reservoir #3.

Alarm #26: Reservoir #1 Draining or Transfer Malfunction

Troubleshooting for Reservoir #1 draining or transfer malfunctions.

Alarm #27: Reservoir #2 Draining or Transfer Malfunction

Troubleshooting for Reservoir #2 draining or transfer malfunctions.

Alarm #28: Reservoir #3 Draining or Transfer Malfunction

Troubleshooting for Reservoir #3 draining or transfer malfunctions.

Alarm #29: Chamber Pressure Abnormal

Troubleshooting for abnormal chamber pressure.

Alarm #30: Dosing System Communication Failure

Troubleshooting communication failures with the dosing system.

Alarm #31: Chemical #1 Low Level

Troubleshooting for low level of Chemical #1.

Alarm #32: Chemical #2 Low Level

Troubleshooting for low level of Chemical #2.

Alarm #33: Chemical #3 Low Level

Troubleshooting for low level of Chemical #3.

Alarm #34: Chemical #4 Low Level

Troubleshooting for low level of Chemical #4.

Alarm #35: Chemical #5 Low Level

Troubleshooting for low level of Chemical #5.

Alarm #36: Compressed Air Not Detected

Troubleshooting for absence of compressed air.

Alarm #37: Reservoir #1 Too Long to Heat

Troubleshooting for Reservoir #1 taking too long to heat.

Alarm #38: Water Recirculation Pressure Switch Defective

Troubleshooting for defective water recirculation pressure switch.

Alarm #39: PV Chemical Injection with Pump #1 Out of Range

Troubleshooting for PV chemical injection out of range for Pump #1.

Alarm #40: PV Chemical Injection with Pump #2 Out of Range

Troubleshooting for PV chemical injection out of range for Pump #2.

Alarm #41: PV Chemical Injection with Pump #3 Out of Range

Troubleshooting for PV chemical injection out of range for Pump #3.

Alarm #42: PV Thermal Temperature Out of Range

Troubleshooting for PV thermal temperature out of range.

Alarm #48: Over Temperature Switch Tripped

Troubleshooting for tripped over temperature switches.

Alarm #49: Dosing System Software Outdated

Troubleshooting for outdated dosing system software.

Alarm #50: Analog Sensor Calibrations Reset to Factory Default Values

Troubleshooting for analog sensor calibrations reset to default.

Alarm #51: Cycles Returned to Factory Default Values, Warn Supervisor!

Troubleshooting for cycle parameters reset to factory defaults.

Warning #1: Hot Water Pressure Below Requirement

Warning #2: Pure Water Pressure Below Requirement

Warning #3: Hot Water Pressure Above Requirement

Warning #4: Pure Water Pressure Above Requirement

Warning #5: Cold Water Pressure Below Requirement

Warning #6: Cold Water Pressure Above Requirement

Warning #7: Cycle Parameters Have Been Reset to Factory Default Values

Warning #8: Cycle Chemical Injection Rates Have Been Reset to Factory Default Values

Warning #9: Temperature Not Reached by Reservoir #1 During DECONTAM Cycle Wash

Troubleshooting temperature not reached in Reservoir #1 during DECONTAM.

Windows Message: SterisHMI.exe is not responding

Bar code reader (accessory) does not operate properly

Chamber does not drain properly

Troubleshooting for improper chamber draining.

Chemical leaks from mechanical core dosing system

Troubleshooting chemical leaks from the dosing system.

Display shows blank red screen with an error message

Troubleshooting blank red screen error messages.

Door fails to open

Troubleshooting issues with the door failing to open.

Door obstruction

Troubleshooting door obstructions.

Doors do not open completely

Troubleshooting doors that do not open completely.

Doors open and/or close too quickly

Troubleshooting doors opening or closing too quickly.

Doors open and/or close too slowly and/or vibrate

Troubleshooting doors opening/closing slowly or vibrating.

Excessive vapor exhausting from chamber vacuum/pressure safety damper

Excessive vapor exhausting from doors

Foam in chamber or inside reservoirs

Troubleshooting foam in chamber or reservoirs.

Floor tilting system lifting too slowly, not lifting or stays in upper position

Troubleshooting floor tilting system issues.

Generated printout is light or blank, or parts of characters are missing

Incomplete drying

Troubleshooting incomplete drying of loads.

Insufficient or no water entering chamber through horizontal traveler spray arms

Troubleshooting water flow issues in traveler spray arms.

Insufficient or no water entering chamber through manifolded rack

Interior light is OFF when building electrical supply disconnect switch is ON

Load comes out dirty at cycle end

Manifolded rack spray arms not turning

No audible signal when alarm occurs, when cycle is completed, etc.

No display on touch screen(s)

Noisy Drying Fan

Noisy exhaust fan

Paper is not taken up into paper takeup

Phase stops for no apparent reason

Printer does not work

Printer printout is erratic

Printer works but does not print

Recirculation pump abnormally noisy

Touch screen does not work properly

Travelers moving too slowly

Travelers vibrating

Water leaks from washer/disinfector

Replacement Parts and Products

Ordering Replacement Parts and Consumables