Stryker 4100 Series - User Manual

Instructions for Use
2020-07 4100-005-700 Rev-AB www.stryker.com
ENGLISH (EN)
ESPAÑOL (ES)
DEUTSCH (DE)
FRANÇAIS (FR)
ITALIANO (IT)
NEDERLANDS (NL)
SVENSKA (SV)
DANSK (DA)
SUOMI (FI)
PORTUGUÊS (PT)
NORSK (NO)
POLSKI (PL)
ΕΛΛΗΝΙΚΑ (EL)
TÜRKÇE (TR)
РУССКИЙ (RU)
日本語 (JA)
中文 (ZH)
한국어 (KO)
Cordless Driver and
Universal Driver
Attachments
4100-XXX-XXX Series
4505-XXX-XXX Series

Stryker 4100 Series Specifications

General

Brand	Stryker
Model	4100 Series
Category	Tools
Language	English

Summary

Cordless Driver and Universal Driver Attachments

Introduction

Indications For Use

Contraindications

For Use With

Safety Directives

Sagittal Saw Attachment

Description

Sagittal Saw Attachment (REF 4100-400-000) Length: 112.0 mm; Diameter: 22.5 mm; Weight: 172.0 g

Accessories

NOTE: For a complete list of accessories, contact your Stryker sales representative.

Locking Keyless Chucks

Description

1/4 inch (6.4 mm) Locking Keyless Chuck (REF 4505-133-000) Handles wires, pins, and drill bits up to 1/4 inch (6.4 mm) diameter.

Instructions

WARNING: You must manually close the chuck jaws to secure the accessory. Operating the handpiece to automatically close the jaws on the accessory may result in injury to the user.

Duty Cycle

See the instructions for use supplied with the handpiece.

Keyless Drill Chucks

Description

1/4 inch Keyless Drill Chuck (REF 4100-133-000) Handles wires, pins, and drill bits up to 1/4 inch (6.4 mm) diameter.

Instructions

WARNING: You must manually close the chuck jaws to secure the accessory. Operating the handpiece to automatically close the jaws on the accessory may result in injury to the user.

Duty Cycle

See the instructions for use supplied with the handpiece.

Chucks with Key

Description

1/4 inch Keyed Chuck (REF 4100-131-000) Handles wires, pins, and drill bits up to 1/4 inch (6.4 mm) diameter.

Instructions

1. Use the chuck key to open the chuck jaws. 2. Insert the accessory into the center of the chuck jaws.

Duty Cycle

See the instructions for use supplied with the handpiece.

Wire and Pin Collets

Description

Wire Collet (REF 4100-062-000) This collet holds K-wires having diameters from 0.028 – 0.071 inch (0.7 – 1.8 mm).

Instructions

1. Load the wire or pin into the nose of the collet or back cap of the handpiece. 2. Move the safety switch out of the safety position.

Duty Cycle

See the instructions for use supplied with the handpiece.

Drill and Reamer Attachments

Description

Trinkle Drill (REF 4100-160-000) Accepts tools such as drill bits and automatic screwdrivers with standard Trinkle fitting.

Instructions

1. Slide back the retaining collar. 2. Insert a bit or tool accessory. 3. Release the retaining collar.

Duty Cycle

See the instructions for use supplied with the handpiece.

Radiolucent Attachments

Description

Right Angle Drive - Radiolucent (REF 4100-355-000) See the instructions for use supplied with this attachment.

Bur Attachments

Description

1:1 Bur Attachment (REF 4100-600-000) See the instructions for use supplied with this attachment.

T-Latch Attachment

Description

T-Latch Attachment (REF 4100-120-000) See the instructions for use supplied with this attachment.

Troubleshooting

Care Instructions

Definitions

Specifications

Environmental Conditions