Tektronix DSA8200 Series User Manual

Appendix C: Factory Default Setup Values
Command Default Values
MATH<x>:POSition
0.5
MATH<x>:SCAle
1.000E+000
MATH<x>:SCAle
1
Measurement Default
Values
The following table lists the Measurement f actory default setup values.
Command Default Va
lues
MEASUreme
nt:ANNOtations:STATE
0(OFF)
MEASUrem
ent:MEAS<x>:EYEWindow
20
MEASUre
ment:MEAS<x>:GATing:STATE
0(OFF)
MEASUre
ment:MEAS<x>:JITter
EYECROS
S
MEASUr
ement:MEAS<x>:NOISe
HIGH
MEASUr
ement:MEAS<x>:REFLevel<x>:ABSolute:HIGH
REFLEVEL 1 = 0.000E+000
MEASU
rement:MEAS<x>:REFLevel<x>:ABSolute:LOW
REFLEVEL 1 = 0.000E+000
MEAS
Urement:MEAS<x>:REFLevel<x>:ABSolute:MID
REFLEVEL 1 = 0.000E+000
MEAS
Urement:MEAS<x>:REFLevel<x>:RELative:HIGH
REFLEVEL 1 = 9.000E+001
MEA
SUrement:MEAS<x>:REFLevel<x>:RELative:LOW
REFLEVEL 1 = 1.000E+000
MEA
SUrement:MEAS<x>:REFLevel<x>:RELative:MID
REFLEVEL 1 = 5.000E+001
ME
ASUrement:MEAS<x>:REFLevel<x>:METHod
RELATIVE
ME
ASUrement:MEAS<x>:SOUrce<x>:EDGE:DIRection
FO
RWARD
M
EASUrement:MEAS<x>:SOUrce<x>:EDGE:SLOPe
R
ISE
MEASUrement:MEAS<x>:SOUrce<x>:GATE<x>:POS Gate 1 = 1.800E-008
Gate 2 = 2.300E-008
MEASUrement:MEAS<x>:SOUrce<x>:HILow:METHod AUTO
MEASUrement:MEAS<x>:SOUrce<x>:HILow:TRACk:
HIGH:ENABle
0(OFF)
MEASUrement:MEAS<x>:SOUrce<x>:HILow:TRACk:
HIGH:VALue
0.000e+000
MEASUrement:MEAS<x>:SOUrce<x>:HILow:TRACk:
LOW:ENABle
0(OFF)
MEASUrement:MEAS<x>:SOUrce<x>:HILow:TRACk:
LOW:VALue
0.000E+000
MEASUrement:MEAS<x>:SOUrce<x>:WFM CH1,MAIN
MEASUrement:MEAS<x>:SOUrce<x>:WFMDB:SIGType PULSE
MEASUrement:MEAS<x>:SOUrce<x>:WFMDB:STATE 0(OFF)
MEASUrement:MEAS<x>:STATE 0(OFF)
MEASUrement:MEAS<x>:TYPe
UNDEFINED
MEASUrement:STATIstics:ENABle 0(OFF)
MEASUrement:STATIstics:WEIghting
32
C-4 DSA/CSA/TDS8X00/B Series Programmer Manual

Tektronix DSA8200 Series Specifications

General

Brand	Tektronix
Model	DSA8200 Series
Category	Test Equipment
Language	English