THERMACUT EX-TRAFIRE 105HD - Torch Dimensions FHT-EX 105 TTH; Torch Dimensions FHT-EX 105 TTM; Torch Dimensions FHT-EX 105 TTSM

72 pages

Save Page as PDF

To Next Page

To Previous Page

4 Product description EX-TRAFIRE

105HD

4.3.1 Torch dimensions FHT-EX

105TTH

4.3.2 Torch dimensions FHT-EX

105TTM

4.3.3 Torch dimensions FHT-EX

105TTSM

Fig. 3 Torch dimensions FHT-EX

105TTH

Fig. 4 Torch dimensions FHT-EX

105TTM

Fig. 5 Torch dimensions FHT-EX

105TTSM

Main Page

Default Chapter2
- Table of Contents2
1 Identification5
- Labeling5
- Identification Plate5
- Signs and Symbols Used6
- Classification of the Warnings6
2 Safety7
- Designated Use7
- Obligations of the Operator7
- Warning and Notice Signs8
- Product-Specific Safety Instructions8
- Safety Instructions for the Electrical Power Supply8
- Safety Instructions for Plasma Cutting9
- Personal Protective Equipment9
- Emergency Information9
3 Scope of Delivery10
4 Product Description11
- Assembly and Use11
- Technical Data12
- Technical Data for Cutting Torches FHT-EX14
- 105TTH and FHT-EX 105TTM14
- Torch Dimensions FHT-EX 105TTH16
- Torch Dimensions FHT-EX 105TTM16
- Torch Dimensions FHT-EX 105TTSM16
5 Transport and Positioning17
6 Setting up the Power Supply18
- Connecting to the Gas Supply18
- Connecting the Work Lead18
- Connecting the Power Supply Cable18
- Connecting the Single-Phase Machine18
- Connecting the Three-Phase Machine19
- Connecting the Input Power Plug19
- Connection to a Generator (Optional)20
- Connecting the Cutting Torch21
- Installing the Cutting Torch's Gear Rack22
- Installing Consumables for the Hand and Machine Cutting Torches23
- Aligning FHT-EX ® 105TTM Machine Cutting Torch25
7 Operation of the Power Supply25
- LCD Description26
- Setting the Parameters27
- Selecting the Cutting Mode27
- Connecting the Work Lead28
- Powering on the Machine28
- Manual Cutting Process29
- Manual Grid Cutting and Gouging Process29
- Cutting - Edge Start30
- Piercing31
- Gouging31
- Stopping the Cutting Process33
8 Decommissioning33
9 Maintenance and Cleaning34
- Maintenance and Cleaning Intervals35
10 Faults and Troubleshooting37
11 Disassembly42
12 Disposal43
- Disposal of Materials43
- Disposal of Consumables43
- Packaging43
13 Warranty44
14 Block Diagram44
15 Accessories45
16 FHT-EX 105TTH Hand Cutting Torch Unit46
17 FHT-EX ® 105TTH Consumables for Hand Cutting Torch47
- Cutting Torch 45-85 a47
- Fht-Ex47
  - Cutting Torch 100-105 a48
- FHT-EX ® 105TTH Consumables for Smoothline Hand48
  - Cutting Torch48
18 FHT-EX ® 105TTM Machine Cutting Torch Unit49
- FHT-EX 105TTM Machine Cutting Torch Without Gear Rack49
- FHT-EX 105TTSM Short Machine Cutting Torch50
19 Fht-Ex50
- Cutting Torch51
- Fht-Ex51
  - Cutting Torch 45-85 a51
- Fht-Ex52
  - Cutting Torch 100-105 a52
- FHT-EX ® 105TTM Consumables for Smoothline53
  - Machine Cutting Torch53
- FHT-EX 105TTM Consumables for Marking Machine Cutting Torch54
20 Cut Charts for Mechanized Cutting55
- Cutting, Shielded, with Compressed Air56
- Cutting, Shielded, with Compressed Air57
- Cutting, Shielded, with Compressed Air58
- Cutting, Shielded, with Compressed Air59
- Cutting, Shielded, with Compressed Air60
- Cutting, Shielded, with Compressed Air61
- 100-105 a Cutting, Shielded, with Compressed Air62
- 100-105 a Cutting, Shielded, with Compressed Air63
- A Cutting, Smoothline, Shielded, with Compressed Air64
- A Cutting, Smoothline, Shielded, with Compressed Air65
- Marking, Shielded, with Compressed Air or Argon66
21 Appendix67
- Connecting the Optional CNC Interface67
- Setting the Voltage Divider DIP Switches68
- Enabling the External DC Coil with an External Power Supply68
- Enabling the External AC Coil with an External Power Supply69
- Enabling the Industrially Insulated Module with an External Power Supply69

THERMACUT EX-TRAFIRE 105HD - Torch Dimensions FHT-EX 105 TTH; Torch Dimensions FHT-EX 105 TTM; Torch Dimensions FHT-EX 105 TTSM

Table of Contents

Related product manuals