TiSUN MULTIPLEX User Manual

13
4.4 "Difference control unit" functional block
Settings
Options
Factory setting
Note
Primary sensor (warm)
T1 to T12
Selectable
Heat source temperature sensor
Secondary sensor (cold)
T1 to T12
Selectable

dT max (start)
3 to 40 °C
15 °C
dT max
dT min (stop)
2 to 30 °C
7 °C
dT min
Min. primary sensor
0 to 95 °C
65 °C
Minimum temperature for ON
Max. secondary sensor
15 to 95 °C
15 °C
Maximum tank temperature
Timer (3x)
00.00-24.00
00.00-24.00
3 time frames adjustable (see timer)
Delay
-900 to +900sec.
0sec.
pre(- sec.) and after(+ sec.) output delay
Some Examples  individual or multiple plate heat exchanger
System 3
Duplex
System 3 (1PHE)
Multiplex
System 3 (2 PHE)
Multiplex
P1= Dt(T1,T2) P2= Dt(T1,T4)
P1= Dt(T1,T2) P2= Dt(T1,T4)
P1= Dt(T1,T2) P2= Dt(T1,T4)
Diff 1 = Px = Dt(Tx,T2)
No PHE
Diff 1 = Px = Dt(Tx,T4)
Diff 2 = Py = Dt(Ty,T4)
System 9
Multiplex
System 9 (1PHE)
Multiplex
System 10
Multiplex
System 10 (1PHE)
Multiplex
P1= Dt(T1,T2 or T3) P2=
Dt(T4,T2orT3)
P1= Dt(T1,T2 or T3) P2=
Dt(T4,T2orT3)
P1= Dt(T1,T2 or T3) P2=
Dt(T1,T2)
P1= Dt(T1,T2 or T3) P2=
Dt(T1,T2)
P7= Dt(T1 or T4,T3)
P7= Dt(T1 or T4,T3)
P5= Dt(T1,T3)
P5= Dt(T1,T3)
No PHE
Diff 1 = Px = Dt(Tx,T3)
No PHE
Diff 1 = Px = Dt(Tx,T3)
System 11
Multiplex
System11 (1PHE)
Multiplex
System 12
Multiplex
System12 (1PHE)
Multiplex
P1= Dt(T1,T2orT3orT7) P2=
Dt(T1,T2)
P1= Dt(T1,T2orT3orT7) P2=
Dt(T1,T2)
P1= Dt(T1,T2orT3orT7orT8)
P2= Dt(T1,T2)
P1= Dt(T1,T2orT3orT7orT8) P2=
Dt(T1,T2)
P5= Dt(T1,T3) P7= Dt(T1,T7)
P5= Dt(T1,T3) P7= Dt(T1,T7)
P5= Dt(T1,T3) P7= Dt(T1,T7)
P8= Dt(T1,T8)
P5= Dt(T1,T3) P7= Dt(T1,T7) P8=
Dt(T1,T8)
No PHE
Diff 1 = Px = Dt(Tx,T7)
No PHE
Diff 1 = Px = Dt(Tx,T8)

TiSUN MULTIPLEX Specifications

General

Brand	TiSUN
Model	MULTIPLEX
Category	Control Unit
Language	English