Toro 31598 - Page 44

To Next Page

To Previous Page

Figure50

Figure51

Figure52

FrontCuttingUnit

•Castorforkshaftbushings(2)(Figure53)

•Spindleshaftbearings(5)(locatedonspindle

housing)(Figure53)

•Idlerarmpivotbushings(3)(locatedontheidler

pivotshaft)(Figure53)

Figure53

FrontLiftAssemblies

•Liftarmbushings(2)(Figure54)

•Liftarmballjoints(2)(

Figure54)

•FrontDeckLiftcylinderpivots(2)(Figure54)

Figure54

SideCuttingUnits(perside)

•Castorforkshaftbushing(4)(Figure55)

•Spindleshaftbearings(3each)(locatedonspindle

housing)(Figure55)

•Idlerarmpivotbushings(2)(locatedontheidler

pivotshaft)(

Figure55)

Main Page

Introduction2
Table of Contents3
Safety4
- Safe Operating Practices4
- Toro Mower Safety6
- Maintenance and Storage7
- Sound Power Level8
- Sound Pressure Level8
- Vibration Level8
- Safety and Instructional Decals9
Setup15
- Remove Side Deck Shipping Strap and Brace16
- Lower Front Deck Winglets16
- Level Front Center Deck17
- Level Winglet Decks to Front Center Deck17
- Checking Tire Pressure18
- Checking Fluid Levels18
- Greasing Machine19
Product Overview19
- Controls19
- Specifications27
- Attachments/Accessories27
Operation28
- Checking the Engine Oil Level28
- Checking the Cooling System28
- Checking the Hydraulic System28
- Adding Fuel28
- Checking the Tire Pressure29
- Checking the Torque of Wheel Lug Nuts29
- Adjusting the Height-Of-Cut29
- Adjusting the Skids32
- Adjusting the Cutting Unit Anti-Scalp Rollers32
- Checking the Mismatch between Cutting Units33
- Adjusting the Mirrors34
- Aiming the Headlights34
- Starting and Stopping the Engine34
- Checking the Interlock Switches35
- Pushing or Towing the Machine35
- Jacking Points36
- Tie Downs37
- Operating Characteristics37
- Reversing Fan Operation38
- Operating Tips39
Maintenance40
- Recommended Maintenance Schedule(S)40
  - Service Interval Chart41
- Premaintenance Procedures42
- Inner Wing Deck Covers42
Lubrication43
- Greasing the Bearings and Bushings43
Engine Maintenance45
- Air Cleaner Maintenance45
- Servicing the Engine Oil46
- Adjusting the Valve Clearance47
Fuel System Maintenance48
- Servicing the Fuel System48
- Servicing the Water Separator48
- Replacing the Fuel Filter49
Electrical System Maintenance50
- Fuses50
- Battery Care51
- Jump Starting / Battery Charging51
- Recalibrate Traction Pedal51
Drive System Maintenance52
- Adjusting the Traction Pedal Angle52
- Checking the Planetary Gear Drive Oil52
- Changing the Planetary Gear Drive Oil52
- Checking the Rear Wheel Toe-In53
Cooling System Maintenance54
- Checking the Cooling System54
- Servicing the Engine Cooling System55
Brake Maintenance55
- Adjusting the Service Brakes55
Belt Maintenance56
- Servicing the Alternator Belt56
- Servicing the Compressor Belt56
- Replacing the Blade Drive Belts56
- Front Cutting Unit56
- Side Cutting Decks57
Hydraulic System Maintenance58
- Checking the Hydraulic Fluid58
- Checking the Hydraulic Filter Service Indicators (if so Equipped)59
- Changing the Hydraulic Fluid and Filters60
- Checking the Hydraulic Lines and Hoses61
- Hydraulic System Test Ports61
Mower Maintenance61
- Pivoting (Tilting) the Front Cutting Unit Upright61
- Pivoting the Front Cutting Unit down62
- Adjusting the Cutting Unit Pitch62
- Servicing the Castor Arm Bushings63
- Servicing the Castor Wheels and Bearings64
Blade Maintenance65
- Checking for a Bent Blade65
- Removing and Installing the Cutter Blade(S)65
- Inspecting and Sharpening the Cutter Blade(S)65
  - Correcting the Cutting Unit Mismatch66
- Miscellaneous Maintenance67
Storage69
- Preparing for Seasonal Storage69
Schematics70
The Toro Total Coverage Guarantee84

Toro 31598 - Page 44

Table of Contents

Related product manuals