Toshiba E-STUDIO2006 - Page 18

e-STUDIO2006/2306/2506/2007/2307/2507/2303A/2303AM/2803AM/2309A/2809A © 2013-2017 TOSHIBA TEC CORPORATION All rights reserved
CONTENTS
4
4.8.1 Fuser unit......................................................................................................... 4-77
4.8.2 Fuser unit cover/Fuser unit guide .................................................................... 4-78
4.8.3 Center heater lamp (LAMP1) .......................................................................... 4-80
4.8.4 Side heater lamp (LAMP2) .............................................................................. 4-81
4.8.5 Base unit.......................................................................................................... 4-82
4.8.6 Separation finger ............................................................................................. 4-83
4.8.7 Pressure roller ................................................................................................. 4-84
4.8.8 Fuser roller/Fuser roller bushing...................................................................... 4-85
4.8.9 Fuser center thermostat (THMO1) / Fuser front thermostat (THMO2) ............ 4-87
4.8.10 Center thermistor (THMS1) / Side thermistor (THMS2) /
Edge thermistor (THMS3)................................................................................ 4-88
4.8.11 Exit sensor (S3) ............................................................................................... 4-91
4.8.12 Exit roller.......................................................................................................... 4-92
4.9 Fuser/Exit Unit <23LA/23LM/28LM/23HA/28HA> ........................................................... 4-94
4.9.1 Fuser unit......................................................................................................... 4-97
4.9.2 Exit sensor (S3) ............................................................................................... 4-98
4.9.3 Fuser unit cover/Fuser unit guide .................................................................. 4-100
4.9.4 Center heater lamp (LAMP1) ........................................................................ 4-103
4.9.5 Side heater lamp (LAMP2) ............................................................................ 4-104
4.9.6 Base unit........................................................................................................ 4-105
4.9.7 Pressure roller ............................................................................................... 4-106
4.9.8 Separation finger ........................................................................................... 4-107
4.9.9 Fuser roller/Fuser roller bushing.................................................................... 4-108
4.9.10 Fuser center thermostat (THMO1) / Fuser front thermostat (THMO2) .......... 4-109
4.9.11 Center thermistor (THMS1) / Side thermistor (THMS2) /
Edge thermistor (THMS3).............................................................................. 4-111
4.9.12 Exit roller........................................................................................................ 4-113
4.10 Automatic duplexing unit (ADU): Option <20L/23L/25L/20H/23H/25H> ....................... 4-116
4.10.1 Automatic duplexing unit (ADU)..................................................................... 4-116
4.10.2 ADU sensor (S8)............................................................................................ 4-117
4.10.3 Fuser guide unit ............................................................................................. 4-117
4.10.4 Paper exit motor (M6) .................................................................................... 4-118
4.10.5 ADU clutch (CLT4)......................................................................................... 4-119
4.10.6 ADU fan duct unit........................................................................................... 4-120
4.10.7 ADU lower transport roller ............................................................................. 4-120
4.10.8 ADU upper transport roller............................................................................. 4-121
4.10.9 ADU transport roller ....................................................................................... 4-122
4.11 Automatic duplexing unit (ADU): <23LA/23LM/28LM/23HA/28HA> ............................. 4-123
4.11.1 Automatic duplexing unit (ADU)..................................................................... 4-123
4.11.2 ADU sensor (S8)............................................................................................ 4-124
4.11.3 Fuser guide unit ............................................................................................. 4-124
4.11.4 Paper exit motor (M6) .................................................................................... 4-125
4.11.5 ADU clutch (CLT4)......................................................................................... 4-126
4.11.6 ADU fan duct unit........................................................................................... 4-126
4.11.7 ADU lower transport roller ............................................................................. 4-127
4.11.8 ADU upper transport roller............................................................................. 4-128
4.11.9 ADU transport roller ....................................................................................... 4-128
4.12 Installation and Replacement of Options <20L/23L/25L/20H/23H/25H> ...................... 4-129
4.12.1 Reversing Auto Document Feeder (RADF) ................................................... 4-129
4.12.2 Paper feed unit (PFU).................................................................................... 4-130
4.13 Installation and Replacement of Options <23LA/23LM/28LM/23HA/28HA>................. 4-134
4.13.1 Reversing Auto Document Feeder (RADF) ................................................... 4-134
4.13.2 Paper feed unit (PFU).................................................................................... 4-135
5. SELF-DIAGNOSIS MODES .......................................................................................... 5-1
5.1 Overview ........................................................................................................................... 5-1
5.2 Input Check (Test Mode 03) ............................................................................................. 5-5
5.3 Output Check (Test Mode 03)........................................................................................... 5-6
5.4 Test Print Mode (Test Mode 04) ....................................................................................... 5-7