e-STUDIO281c/351c/451c © 2005 - 2008 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 12
CC71 Finisher related
service call
Punch ROM checksum error: Abnormality of check-
sum value on Hole punch controller PC board is
detected when the power is turned on. [MJ-1101
(when MJ-6101 is installed)]
P. 5 - 7 9
CC72 Punch RAM read/write error: Abnormality of check-
sum value on Hole punch controller PC board is
detected when the power is turned on. [MJ-1101
(when MJ-6101 is installed)]
P. 5 - 7 9
CC80 Front alignment motor abnormality: Front alignment
motor is not rotating or front aligning plate is not
moving normally. [MJ-1022]
Front aligning plate motor abnormality: Front align-
ing plate motor is not rotating or aligning plate is not
moving normally. [MJ-1023/1024]
P. 5 - 8 0
Rear alignment motor abnormality: The rear align-
ment motor is not rotating or the rear alignment
plate is not moving normally. [MJ-1101]
P. 5 - 8 0
CC90 Upper stack tray lift motor abnormality: The upper
stack tray lift motor is not rotating or the upper stack
tray is not moving normally. [MJ-1022]
P. 5 - 8 1
CCA0 Lower stack tray lift motor abnormality: The lower
stack tray lift motor is not rotating or the lower stack
tray is not moving normally. [MJ-1022]
P. 5 - 8 2
CCB0 Rear jogging motor abnormality: The rear jogging
motor is not rotating or the rear jogging plate is not
moving normally. [MJ-1022]
P. 5 - 8 2
CCD0 Stack ejection motor abnormality: Stack ejection
motor or stack ejection roller is not rotating nor-
mally. [MJ-1023/1024]
P. 5 - 8 3
CCE0 Paper trailing edge assist motor abnormality: Paper
trailing edge assist motor is not rotating or paper
trailing edge assist is not moving normally. [MJ-
1023/1024]
P. 5 - 8 3
CCF0 Gear changing motor abnormality: Gear changing
motor is not rotating normally. [MJ-1023/1024]
P. 5 - 8 3
CDE0 Paddle motor abnormality: The paddle motor is not
rotating or the paddle is not rotating normally. [MJ-
1101]
P. 5 - 8 4
CE00 Communication error between finisher and punch
unit: Communication error between finisher control-
ler PC board and punch controller PC board [MJ-
1023/1024 (when MJ-6004 is installed)]
[MJ-1101 (when MJ-6101 is installed)]
P. 5 - 8 4
CE10 Image control related
service call
Image quality sensor abnormality (OFF level): The
output value of this sensor is out of a specified
range when sensor light source is OFF.
P. 5 - 8 6
CE20 Image quality sensor abnormality (no pattern level):
The output value of this sensor is out of a specified
range when the image quality control test pattern is
not formed.
P. 5 - 8 7
CE40 Image quality control test pattern abnormality: The
test pattern is not formed normally.
P. 5 - 8 8
CE50 Temperature/humidity sensor abnormality: The out-
put value of this sensor is out of a specified range.
P. 5 - 8 9
CE90 Drum thermistor abnormality: The output value of
the drum thermistor is out of a specified range.
P. 5 - 8 9
Error code Classification Contents Troubleshooting
07/04
To Next Page
Loading...
