EasyManua.ls Logo

Trane Tracer Summit - User Manual

Trane Tracer Summit
272 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
BMTW-SVN01F-EN
Hardware and Software
Installation
TRACER SUMMIT™
Version 16

Table of Contents

Other manuals for Trane Tracer Summit

Preview: Installation Instructions
Installation Instructions2 pages
Preview: Hardware And Software Installation
Hardware And Software Installation152 pages

Questions and Answers

  • A
    Amy ClarkJul 27, 2025
    What causes a Trane Tracer Summit BCU panel mismatch error, and how can I resolve it?
    • M
      Michael AtkinsJul 28, 2025
      A Trane Control Systems BCU panel mismatch error can occur due to active panel checking. To resolve this, verify that the device ID of the panel you are attempting to download matches the Site Configuration address for that panel. Also, check if the panel type in the Site Configuration editor matches the panel that appears in the Panel Mismatch error message. If the Site Configuration setup for the panel matches the BCU hardware, but you still get a panel mismatch error, properly seat or change the failed hardware.
  • D
    Diane CarterAug 3, 2025
    What to do if my Trane Control Systems BCU locks up?
    • A
      April TaylorAug 4, 2025
      If your Trane Control Systems BCU locks up, it could be due to several reasons: * A building power disturbance: Cycling the power on the BCU should clear this up. For repeated issues, consider installing an external device to protect against AC power transients. * A power disturbance through the modem line: Cycling the BCU power should resolve this. * Strong EMI/RFI interference: Avoid using cell phones and walkie-talkies within 6 ft of the BCU. * Too many UCM and program objects: Estimate BCU memory usage with the BCU sizing spreadsheet before connecting UCMs and programming the BCU. * BCUs programmed to route alarms/events to remote Tracer Summit PC Workstations: Ensure remote workstations are connected periodically to harvest the alarms.
  • J
    Justin DoyleAug 12, 2025
    How to fix a Trane Tracer Summit BCU that does not respond?
    • E
      Erin MarksAug 12, 2025
      If your Trane Control Systems BCU is not responding, check the following: * Verify the BCU has the correct AC supply voltage. * Check for the proper device address on the BCU logic board and the ARCNET card (if applicable). * Ensure the BCU power switch is turned on. * Verify the BCU LEDs sequence properly on power up and that the ARCNET or Ethernet card LEDs show normal activity. * Check the ARCNET or Ethernet cable connections. * Perform a Clear Code, Database, RAM, and Reset using the BCU DIP switches.
  • G
    gina07Aug 18, 2025
    Why is my Trane Tracer Summit Control Systems BCU not communicating via modem?
    • T
      Thomas BrooksAug 19, 2025
      If your Trane Control Systems BCU is not communicating via modem, here are some things to check: * Verify that the BCU has a modem object. * Check for a dial tone and verify that the phone can make and receive calls. * Consider using an in-line transient protection device on the phone line. * If the phone line goes through a local phone system, ensure additional wait times and access numbers are programmed into the phone numbers. * Verify that the correct phone number is being used when attempting to dial into a BCU.

Summary

Chapter 2 BCU Mounting and Power Wiring

BCU Mounting and Power Wiring for North American Installations

Provides procedures for mounting and wiring the BCU for North American installations.

Installing and Wiring the BCU Logic Board

Describes the process of installing and wiring the BCU logic board assembly.

Chapter 4 UCM Communication-Link Wiring

Chapter 5 UCM Wiring and Addressing

Chapter 6 Network Wiring

BACnet-Device IDs

Explains the importance and setting of BACnet device IDs for BCUs and PC Workstations.

IP Installation Procedures

Provides steps for installing Tracer Summit on a shared IP network, including preinstallation.

Chapter 7 BCU Modem Installation

Installing a Modem Card

Provides the general procedure for installing an internal modem card into the BCU.

Chapter 8 Installing Tracer Summit

Installing Tracer Summit using Windows XP or Windows 2000

Step-by-step guide for installing Tracer Summit software on Windows XP or Windows 2000.

Configuring BCUs for BACnet;IP Communications

Explains how to configure BCUs for BACnet/IP communications using provided utilities.

Chapter 11 Troubleshooting

BCU Does Not Respond

Provides a checklist for troubleshooting a BCU that does not respond to commands.

BCU Locks Up

Describes common causes and solutions for a BCU periodically locking up.

BCU Panel Mismatch Error

Explains how to resolve errors where BCU hardware does not match the Site Configuration.

Trane Tracer Summit Specifications

General IconGeneral
ManufacturerTrane
TypeBuilding Automation System
Communication ProtocolBACnet, Modbus
User InterfaceGraphical User Interface (GUI)
ScalabilityScalable from small to large buildings
Energy ManagementAdvanced energy management strategies, scheduling, and reporting
Alarm ManagementComprehensive alarm handling and notifications
ReportingCustomizable reports and analytics
Remote AccessYes, via web-based interface

Related product manuals