Trimble 5700 - 5700 AND 5800 APPENDIXES

216 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

SECTION

III

I5700 and 5800

APPENDIXES

Table of Contents

5700/5800 GPS Receiver1
Contents5
Introduction13
- Related Information13
- Technical Assistance14
- Your Comments14
5700 GPS RECEIVER15
Overview17
- Introduction18
- Features18
- Use and Care19
- COCOM Limits20
Setting up the Receiver21
- Introduction22
- Parts of the Receiver22
- Setup Guidelines28
- Postprocessed Setup30
- PoleMounted Setup32
- Backpack Setup38
- Other System Components40
General Operation47
- Introduction48
- Button Functions48
- LED Behavior49
- Starting and Stopping the Receiver51
- Logging Data52
  - Logging internally52
  - Logging to a Trimble controller53
- Resetting to Defaults53
- Formatting a CompactFlash Card54
- Batteries and Power54
Configuration61
- Introduction62
- Configuring the Receiver in Real Time62
- Configuring the Receiver Using Application Files63
- Application Files63
Transferring Data69
- Introduction70
- Connecting to the Office Computer71
- Transferring Data73
- Transferring Files Directly from a CompactFlash Card74
- Deleting Files in the Receiver76
- Supported File Types76
Software Utilities77
- Introduction78
- GPS Configurator Software78
  - Installing GPS Configurator78
  - Configuring the 5700 receiver79
- Configuration Toolbox Software80
  - Installing Configuration Toolbox80
  - Creating and editing application files80
- WinFlash Software83
Specifications89
- Introduction90
- Physical Specifications90
- Positioning Specifications91
- Technical Specifications92
Default Settings93
- Introduction94
- Default Settings95
- Resetting to Factory Defaults96
- Examples97
Cables and Connectors101
- Introduction102
- Port 1, 2, and 3 Connectors102
- Power/serial data cable104
- Event Marker/1PPS Cable105
- GPS Antennas and Cables107
Event Marker Input and 1PPS Output109
- Introduction110
- Event Marker Input110
  - Enabling and configuring event marker input110
- 1PPS Output114
5800 GPS RECEIVER119
Overview121
- Introduction122
- Features122
- Use and Care124
- COCOM Limits124
Setting up the Receiver125
- Introduction126
- Parts of the Receiver126
  - Front panel126
  - Lower housing127
- Setup Guidelines129
- PoleMounted Setup130
- Other System Components131
  - Radios131
  - Cellular modems and external radios132
General Operation135
- Introduction136
- Button Functions137
- LED Behavior137
  - LED flash patterns138
- Starting and Stopping the Receiver138
- Logging Data139
  - Logging internally139
  - Logging to a Trimble controller140
- Resetting to Defaults140
- Batteries and Power140
Configuration143
- Introduction144
- Configuring the Receiver in Real Time144
- Configuring the Receiver Using Application Files145
- Application Files145
Software Utilities149
- Introduction150
- GPS Configurator Software150
  - Installing GPS Configurator150
  - Configuring the 5800 receiver151
- Configuration Toolbox Software152
  - Installing Configuration Toolbox152
  - Creating and editing application files152
- WinFlash Software155
Specifications161
- Introduction162
- Physical Specifications162
- Positioning Specifications163
- Technical Specifications164
Default Settings165
- Introduction166
- Default Settings167
- Resetting to Factory Defaults168
  - Default behavior168
  - Power up settings168
Cables and Connectors169
- Introduction170
- Port 1 and 2 Connectors170
- Power/Serial Data Cables172
5700 AND 5800 APPENDIXES175
NMEA-0183 Output177
- Introduction178
- NMEA-0183 Outputs178
- Common Message Elements180
  - Message values180
- NMEA Messages181
RTCM Output195
- RTCM Output196
- Message Scheduling197
Troubleshooting199
Index205

Related product manuals

Trimble EZ-Guide 500

Trimble EZ-Guide 250